IOb-SoC-OpenCryptoLinux

IOb-SoC-OpenCryptoLinux is a System-on-Chip (SoC) template comprising an open-source RISC-V processor (VexRiscv), an internal boot memory subsystem, a UART, and an interface to external memory. The external memory interface is a 3rd party memory controller IP (typically a DDR controller) using an AXI4 master bus.

Getting Started (Quickly)

This section offers a quick guide for users to start using IOb-SoC-OpenCryptoLinux. The following commands streamline the setup process for simulation and running on an FPGA board:

# Clone the repository
git clone --recursive git@github.com:IObundle/iob-soc-opencryptolinux.git
# Navigate to the project directory
cd iob-soc-opencryptolinux
# Simulate bare-metal firmware with IVerilog and Verilator
make sim-test
# Simulate the Linux OS with Verilator
make sim-test-linux
# Run Linux on the KU board by default
make fpga-run
# After running `fpga-run`, select either bare-metal firmware (with `RUN_LINUX` is 0) or the Linux OS (with `RUN_LINUX` is 1)
make fpga-connect RUN_LINUX=0

These commands aim to expedite the setup process for both simulation and FPGA board execution. Adjust the values as needed for your specific use case.

Differences to IOb-SoC

This section outlines the distinctions between IOb-SoC and IOb-SoC-OpenCryptoLinux.

Compared to IOb-SoC, IOb-SoC-OpenCryptoLinux features a distinct CPU and employs AXI in the internal signals, deviating from the IOb-bus used by IOb-SoC. Another significant difference is the placement of firmware, as the one in IOb-SoC-OpenCryptoLinux always resides in external memory.

Additionally, the bootloader in IOb-SoC-OpenCryptoLinux differs from that in IOb-SoC. In IOb-SoC-OpenCryptoLinux, the bootloader is directly loaded into internal RAM, whereas in IOb-SoC, the bootloader binary starts in ROM and is then copied to RAM.

The boot control unit in IOb-SoC-OpenCryptoLinux, unlike IOb-SoC, is a distinct module and exclusively manages the boot process state. On the software side, the IOb-SoC-OpenCryptoLinux bootloader initially loads a file named iob_mem.config, which specifies the files and their respective memory addresses to be copied into external memory.

Nix environment

You can use nix-shell to run IOb-SoC-OpenCryptoLinux in a Nix environment with all dependencies available except for Vivado and Quartus for FPGA compilation and running.

After installing nix-shell, it can be initialized by calling any Makefile target in the IOb-SoC-OpenCryptoLinux root directory, for example

make setup

The first time it runs, nix-shell will automatically install all the required dependencies. This can take a couple of hours, but after that, you can enjoy IOb-SoC-OpenCryptoLinux and not worry about installing software tools.

Ethernet simulation

The ethernet simulation requires setting up dummy interfaces with eth-[SIMULATOR] that require sudo: Setup the following interfaces with the commands:

sudo modprobe dummy
sudo ip link add eth-icarus type dummy
sudo ifconfig eth-icarus up
sudo ip link add eth-verilator type dummy
sudo ifconfig eth-verilator up

Make dummy interfaces permanent:

Add dummy to /etc/modules
Create /etc/network/if-pre-up.d/dummy-eth-interfaces with:

#!/usr/bin/env bash

# Create eth-SIMULATOR dummy interfaces
ip link add eth-icarus type dummy
ifconfig eth-icarus up
ip link add eth-verilator type dummy
ifconfig eth-verilator up

Set script as executable:

# Set script as executable
sudo chmod +x /etc/network/if-pre-up.d/dummy-eth-interfaces

Ethernet Receiver MAC Address

The current ethernet setup uses a fake receiver MAC address (RMAC_ADDR) common for all simulators and boards. To receive ethernet packets for any destination address, the interface connected to the board needs to be in premiscuous mode. Check premiscuous mode with the command:

ip -d link
# check for promiscuity 1

Set promiscuity to 1 with the command:

sudo ip link set [interface] promisc on

Ethernet RAW frame access

The system's Python scripts need RAW frame access for Ethernet communication. To achieve this, the Python interpreter must have the CAP_NET_RAW capability.

The 'ETHERNET' submodule already includes a Python wrapper that provides RAW frame access. To build the python wrapper, run:

make -C submodules/ETHERNET/scripts/pyRawWrapper

Dependencies

If you prefer, you may install all the dependencies manually and run IOb-SoC-OpenCryptoLinux without nix-shell. The following tools should be installed:

GNU Bash >=5.1.16
GNU Make >=4.3
RISC-V GNU Compiler Toolchain =2022.06.10 (Instructions at the end of this README)
Python3 >=3.10.6
Python3-Parse >=1.19.0

Optional tools, depending on the desired run strategy:

Icarus Verilog >=10.3
Verilator >=5.002
gtkwave >=3.3.113
Vivado >=2020.2
Quartus >=20.1

Older versions of the dependencies above may work but still need to be tested.

Operating Systems

IOb-SoC-OpenCryptoLinux can be used in Linux Operating Systems. The following instructions work for CentOS 7 and Ubuntu 18.04, 20.04, and 22.04 LTS.

Clone the repository

The first step is to clone this repository. IOb-SoC-OpenCryptoLinux uses git sub-module trees, and GitHub will ask for your password for each downloaded module if you clone it by https. To avoid this, setup GitHub access with ssh and type:

git clone --recursive git@github.com:IObundle/iob-soc-opencryptolinux.git
cd iob-soc-opencryptolinux

Alternatively, you can still clone this repository using https if you cache your credentials before cloning the repository, using: git config --global credential.helper 'cache --timeout=<time_in_seconds>'

Configure your SoC

To configure your system, edit the iob_soc_opencryptolinux.py file, which can be found at the repository root. This file has the system configuration variables; hopefully, each variable is explained by a comment.

Set environment variables for local or remote building and running

The various simulators, FPGA compilers, and FPGA boards may run locally or remotely. For running a tool remotely, you need to set two environment variables: the server logical name and the server user name. Consider placing these settings in your .bashrc file so that they apply to every session.

Set up the remote simulator server

Using the open-source simulator Icarus Verilog (iverilog) as an example, note that in submodules/hardware/simulation/icarus.mk, the variable for the server logical name, SIM_SERVER, is set to IVSIM_SERVER, and the variable for the user name, SIM_USER is set to IVSIM_USER.

To run the simulator on the server mysimserver.myorg.com as user ivsimuser, set the following environment variables beforehand, or place them in your .bashrc file:

export IVSIM_SERVER=ivsimserver.myorg.com
export IVSIM_USER=ivsimuser

When you start the simulation, IOb-SoC-OpenCryptoLinux's simulation Makefile will log you on to the server using ssh, then rsync the files to a remote build directory and run the simulation there. If you do not set these variables, the simulator will run locally if installed.

Set up the remote FPGA toolchain and board servers

Using the CYCLONEV-GT-DK board as an example, note that in hardware/fpga/quartus/CYCLONEV-GT-DK/Makefile, the variable for the FPGA tool server logical name, FPGA_SERVER, is set to QUARTUS_SERVER, and the variable for the user name, FPGA_USER, is set to QUARTUS_USER; the variable for the board server, BOARD_SERVER, is set to CYC5_SERVER, and the variable for the board user, BOARD_USER, is set to CYC5_USER. As in the previous example, set these variables as follows:

export QUARTUS_SERVER=quartusserver.myorg.com
export QUARTUS_USER=quartususer
export CYC5_SERVER=cyc5server.myorg.com
export CYC5_USER=cyc5username

In each remote server, the environment variable for the license server used must be defined as in the following example:

export LM_LICENSE_FILE=port@licenseserver.myorg.com;lic_or_dat_file

Create the build directory

IOb-SoC-OpenCryptoLinux uses intricate Python scripting to create a build directory with all the necessary files and makefiles to run the different tools. The build directory is placed in the folder above at ../iob_soc_Vx.y by running the following command from the root directory.

make setup

If you want to avoid getting into the complications of our Python scripts, use the ../iob_soc_Vx.y directory to build your SoC. It only has code files and a few Makefiles. Enter this directory and call the available Makefile targets. Alternatively, using another Makefile in the IOb-SoC-OpenCryptoLinux root directory, the same targets can be called. For example, to run the simulation, the IOb-SoC-OpenCryptoLinux's top Makefile has the following target:

sim-run:
	nix-shell --run 'make clean setup INIT_MEM=$(INIT_MEM) USE_EXTMEM=$(USE_EXTMEM) && make -C ../$(CORE)_V*/ sim-run SIMULATOR=$(SIMULATOR)'

The above target invokes the nix-shell environment to call the local targets clean and setup and the target sim-run in the build directory. Below, the targets available in IOb-SoC-OpenCryptoLinux's top Makefile are explained.

Simulate the system

To simulate IOb-SoC-OpenCryptoLinux's RTL using a Verilog simulator, run

make sim-run [SIMULATOR=icarus!verilator|xcelium|vcs|questa] [INIT_MEM=0|1] [USE_EXTMEM=0|1]

The INIT_MEM variable specifies whether the firmware is initially loaded in the memory, skipping the boot process, and the USE_EXTMEM variable indicates whether an external memory such as DRAM is used, in which case the cache system described above is instantiated.

The Makefile compiles and runs the software in the ../iob_soc_Vx.y/hardware/simulation directory. The Makefile includes the ./hardware/simulation/sim_build.mk, which you can change for your project. To run a simulation test comprising several simulations with different parameters, run

make sim-test

The simulation test contents can be edited in IOb-SoC-OpenCryptoLinux's top Makefile.

Each simulator must be described in the ./submodules/LIB/hardware/simulation/<simulator>.mk file. For example, the file vcs.mk describes the VCS simulator.

The host machine must run an access server, a Python program in ./submodules/LIB/scripts/board_server.py, set up to run as a service. The client connects to the host using the SSH protocol and runs the board client program /submodules/LIB/scripts/board_client.py. Note that the term board is used instead of simulator because the same server/client programs control the access to the board and FPGA compilers. The client requests the simulator for GRAB_TIMEOUT seconds, which is 300 seconds by default. Its value can be specified in the ./hardware/fpga/fpga_build.mk Makefile segment, for example, as

GRAB_TIMEOUT ?= 3600

Build and run on FPGA board

To build and run IOb-SoC-OpenCryptoLinux on an FPGA board, the FPGA design tools must be installed locally or remotely. The FPGA board must also be attached to the local or remote host, not necessarily the same host where the design tools are installed.

Each board must be described under the /submodules/LIB/hardware/fpga/<tool>/<board_dir> directory. For example, the hardware/fpga/vivado/BASYS3 directory contents describe the board BASYS3, which has an FPGA device that can be programmed by the Xilinx/AMD Vivado design tool. The access to the board is controlled by the same server/client programs described above for the simulators. To build an FPGA design of an IOb-SoC-OpenCryptoLinux system and run it on the board located in the board_dir directory, type

make fpga-run [BOARD=<board_dir>] [INIT_MEM=0|1] [USE_EXTMEM=0|1]

To run an FPGA test comparing the result to the expected result, run

make fpga-test

The FPGA test contents can be edited in IOb-SoC-OpenCryptoLinux's top Makefile.

Compile the documentation

To compile documents, the LaTeX software must be installed. Three document types are generated: the Product Brief (pb), the User Guide (ug), and a presentation. To build a given document type DOC, run

make doc-build [DOC=pb|ug|presentation]

To generate the three documents as a test, run

make doc-test

Total test

To run all simulation, FPGA board, and documentation tests, type:

make test-all

Running more Makefile Targets

The examples above are the Makefile targets at IOb-SoC-OpenCryptoLinux's root directory that call the targets in the top Makefile in the build directory. Please explore the available targets in the build directory's top Makefile to add more targets to the root directory Makefile.

Cleaning the build directory

To clean the build directory, run

make clean

Instructions for Installing the RISC-V GNU Compiler Toolchain

Get sources and check out the supported stable version

git clone https://github.com/riscv/riscv-gnu-toolchain
cd riscv-gnu-toolchain
git checkout 2022.06.10

Prerequisites

For the Ubuntu OS and its variants:

sudo apt install autoconf automake autotools-dev curl python3 python2 libmpc-dev libmpfr-dev libgmp-dev gawk build-essential bison flex texinfo gperf libtool patchutils bc zlib1g-dev libexpat-dev

For CentOS and its variants:

sudo yum install autoconf automake python3 python2 libmpc-devel mpfr-devel gmp-devel gawk  bison flex texinfo patchutils gcc gcc-c++ zlib-devel expat-devel

Installation

./configure --prefix=/path/to/riscv --enable-multilib
sudo make -j$(nproc)

This will take a while. After it is done, type:

export PATH=$PATH:/path/to/riscv/bin

The above command should be added to your ~/.bashrc file so you do not have to type it on every session.

Tutorial: Add New Device Driver

Checkout this tutorial for more details on how to add a new device to be tested.

Acknowledgement

The OpenCryptoLinux project was funded through the NGI Assure Fund, a fund established by NLnet with financial support from the European Commission's Next Generation Internet programme, under the aegis of DG Communications Networks, Content and Technology under grant agreement No 957073.

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

README.md

README.md

IOb-SoC-OpenCryptoLinux

Table of Contents

Getting Started (Quickly)

Differences to IOb-SoC

Nix environment

Ethernet simulation

Make dummy interfaces permanent:

Ethernet Receiver MAC Address

Ethernet RAW frame access

Dependencies

Operating Systems

Clone the repository

Configure your SoC

Set environment variables for local or remote building and running

Set up the remote simulator server

Set up the remote FPGA toolchain and board servers

Create the build directory

Simulate the system

Build and run on FPGA board

Compile the documentation

Total test

Running more Makefile Targets

Cleaning the build directory

Instructions for Installing the RISC-V GNU Compiler Toolchain

Get sources and check out the supported stable version

Prerequisites

Installation

Tutorial: Add New Device Driver

Acknowledgement

Files

README.md

Latest commit

History

README.md

File metadata and controls

IOb-SoC-OpenCryptoLinux

Table of Contents

Getting Started (Quickly)

Differences to IOb-SoC

Nix environment

Ethernet simulation

Make dummy interfaces permanent:

Ethernet Receiver MAC Address

Ethernet RAW frame access

Dependencies

Operating Systems

Clone the repository

Configure your SoC

Set environment variables for local or remote building and running

Set up the remote simulator server

Set up the remote FPGA toolchain and board servers

Create the build directory

Simulate the system

Build and run on FPGA board

Compile the documentation

Total test

Running more Makefile Targets

Cleaning the build directory

Instructions for Installing the RISC-V GNU Compiler Toolchain

Get sources and check out the supported stable version

Prerequisites

Installation

Tutorial: Add New Device Driver

Acknowledgement