Skip to content

Latest commit

 

History

History
executable file
·
196 lines (144 loc) · 5.52 KB

README.md

File metadata and controls

executable file
·
196 lines (144 loc) · 5.52 KB

Logo ioBroker RPI-Monitor Adapter

Number of Installations Number of Installations NPM version Downloads

NPM

RPI-Monitor implementation for integration into ioBroker. It is the same implementation as for iobroker.rpi, but with GPIOs.

Important Information

Works only with node >= 0.12

ioBroker must run under root to may control GPIOs.

Installation

After installation you have to configure all required modules via administration page.

After start of iobroker.rpi, all selected modules generates an object tree in ioBroker within rpi.. e.g. rpi.0.cpu

Be sure, that python and build-essential are installed:

sudo apt-get update
sudo apt-get install -y build-essential python

Following Objects are available after selection:

CPU

  • cpu_frequency
  • load1
  • load5
  • load15

Raspberry (vcgencmd is required)

  • cpu_voltage
  • mem_arm
  • mem_gpu

Memory

  • memory_available
  • memory_free
  • memory_total

Network (eth0)

  • net_received
  • net_send

SDCard

  • sdcard_boot_total
  • sdcard_boot_used
  • sdcard_root_total
  • sdcard_root_used

Swap

  • swap_total
  • swap_used

Temperature

  • soc_temp

Uptime

  • uptime

WLAN

  • wifi_received
  • wifi_send

Configuration

On configuration page you can select following modules:

  • CPU
  • Raspberry
  • Memory
  • Network
  • SDCard
  • Swap
  • Temperature
  • Uptime
  • WLAN

Logfiles / Configuration Settings

Features

Todo

Tested Hardware

  • Odroid C1
  • Raspberry Pi 1

GPIOs

You can read and control GPIOs too. All what you need to do is to configure in the settings the GPIOs options (additional tab).

GPIOs

After some ports are enabled following states appear in the object tree:

  • rpi.0.gpio.PORT.state

The numeration of ports is BCM (BroadComm pins on chip). You can get the enumeration with gpio readall. For instance PI2:

+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
|     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
|   2 |   8 |   SDA.1 | ALT0 | 1 |  3 || 4  |   |      | 5V      |     |     |
|   3 |   9 |   SCL.1 | ALT0 | 1 |  5 || 6  |   |      | 0v      |     |     |
|   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 0 | IN   | TxD     | 15  | 14  |
|     |     |      0v |      |   |  9 || 10 | 1 | IN   | RxD     | 16  | 15  |
|  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
|  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
|  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
|     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
|  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
|   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 1 | IN   | GPIO. 6 | 6   | 25  |
|  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
|     |     |      0v |      |   | 25 || 26 | 1 | IN   | CE1     | 11  | 7   |
|   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
|   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
|   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
|  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
|  19 |  24 | GPIO.24 |   IN | 0 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
|  26 |  25 | GPIO.25 |  OUT | 1 | 37 || 38 | 0 | IN   | GPIO.28 | 28  | 20  |
|     |     |      0v |      |   | 39 || 40 | 0 | IN   | GPIO.29 | 29  | 21  |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+

Changelog

1.2.0 (2020-01-17)

  • (janfromberlin) GPIO configuration as output with defined initial value
  • (foxriver76) No longer use adapter.objects
  • (Apollon77) Adjust gpio errors

1.1.1

  • (Apollon77) Error messages for not existing values are logged only once

1.1.0

  • (Apollon77) Nodejs 10 support

1.0.0 (2018-08-20)

  • (bluefox) Admin3 support

0.3.2 (2017-11-29)

  • (Homoran) fixed Mem available readings on Stretch

0.3.1 (2017-01-11)

  • (olifre) Fixup swap_used calculation.

0.2.2 (2016-12-01)

  • (bluefox) Add GPIO direction indication

0.2.2 (2016-11-22)

  • (bluefox) Use BCM enumeration

0.2.1 (2016-10-29)

  • (bluefox) fix start of adapter

0.2.0 (2016-10-23)

  • (bluefox) just version change

0.1.1 (2016-10-13)

  • (bluefox) implement GPIOs control

0.0.4 (2016-03-25)

  • (bluefox) Try catch by eval (bluefox) do not process if exec fails

0.0.3 (2015-12-28)

  • (husky-koglhof) Fixed value calc. Set Value to 2 digits

0.0.2 (2015-12-26)

  • (husky-koglhof) Workaround for node 0.10.x
  • (bluefox) Some Fixes

0.0.1 (2015-12-23)

  • Initial commit. Alpha Version.

License

Copyright (c) 2015-2020 husky-koglhof [email protected]

MIT License