No WIFI_AP found #129
Comments
|
What board are you using? |
NodeMCU-32S |
|
|
$72 |
|
couldn't find Settings for wifi |
|
Are you sure you are using the my_machine.h listed above for compilation?
|
|
YES I am sure,I have tried many times,I don't know what the problem is |
|
Today,I cloned the project and tried to compile it ,succeed,I can find it,Thank you all |
|
I find that when #define N_TOOLS 32 , I can't find wifi_AP |
This is due to running out of settings storage. For now change this line to |
Thank you very much for your reply, which is very helpful to me |
I just cloned the project and tried to compile it using ESP IDF 4.3.6.
All is well,but grblHAL_AP can't be found,I don't know what I did wrong.
This is my_machine.h.
Thanks for your help!
/*
Part of grblHAL
Copyright (c) 2020-2024 Terje Io
grblHAL is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
grblHAL is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with grblHAL. If not, see http://www.gnu.org/licenses/.
*/
// NOTE: Only one board may be enabled!
// If none is enabled pin mappings from generic_map.h will be used
//#define BOARD_BDRING_V3P5 //
#define BOARD_BDRING_V4 //
//#define BOARD_BDRING_I2S6A //
//#define BOARD_BDRING_6X //
//#define BOARD_BDRING_I2S_6PACK_EXT_V2 //
//#define BOARD_ESPDUINO32 //
//#define BOARD_SOURCERABBIT_4AXIS //
//#define BOARD_PROTONEER_3XX //
//#define BOARD_FYSETC_E4 //
//#define BOARD_XPRO_V5 //
//#define BOARD_MKS_DLC32_V2P0 //
//#define BOARD_MKS_TINYBEE_V1 //
//#define BOARD_CNC3040 //
//#define BOARD_BLACKBOX_X32 // NOTE: Enable in CMakeLists.txt to set board specific defaults for the core!
//#define BOARD_ROOTCNC_V2 //
//#define BOARD_ROOTCNC_V3 //
//#define BOARD_ROOTCNC_PRO //
//#define BOARD_JACKPOT // Uses TMC2209 drivers, untested!
//#define BOARD_CNC_BOOSTERPACK //
//#define BOARD_GENERIC_I2S_S3 // Generic map for ESP32-S3 with I2S shift registers for I/O expansion
//#define BOARD_MY_MACHINE // Add my_machine_map.h in the boards directory before enabling this!
//#define BOARD_BLOX
// Configuration
// Uncomment to enable, for some a value > 1 may be assigned, if so the default value is shown.
#ifdef CONFIG_IDF_TARGET_ESP32S3
#define USB_SERIAL_CDC 1 // Serial communication via native USB.
#endif
// Spindle selection:
// Up to four specific spindle drivers can be instantiated at a time
// depending on N_SPINDLE and N_SYS_SPINDLE definitions in grbl/config.h.
// If none are specified the default PWM spindle is instantiated.
// Spindle definitions can be found in grbl/spindle_control.h.
// More here https://github.com/grblHAL/Plugins_spindle
//#define SPINDLE0_ENABLE SPINDLE_HUANYANG1
//#define SPINDLE1_ENABLE SPINDLE_PWM0_NODIR
//#define SPINDLE2_ENABLE SPINDLE_NONE
//#define SPINDLE3_ENABLE SPINDLE_NONE
//#define SPINDLE_OFFSET 1 // Uncomment to enable settings for laser spindle XY-offset.
// **********************
//#define MODBUS_ENABLE 1 // Set to 1 for auto direction, 2 for direction signal on auxillary output pin.
//#define WEBUI_ENABLE 3 // Enable ESP3D-WEBUI plugin along with networking and SD card plugins.
//#define WEBUI_AUTH_ENABLE 1 // Enable ESP3D-WEBUI authentication.
#define WIFI_ENABLE 1 //
#define WIFI_SOFTAP 1 // Use Soft AP mode for WiFi.
//#define ETHERNET_ENABLE 1 // Ethernet streaming. Uses networking plugin.
//#define BLUETOOTH_ENABLE 1 // Set to 1 for native radio, 2 for HC-05 module.
//#define SDCARD_ENABLE 1 // Run gcode programs from SD card. Set to 2 to enable YModem upload.
//#define MPG_ENABLE 1 // Enable MPG interface. Requires a serial stream and means to switch between normal and MPG mode.
// 1: Mode switching is by handshake pin.
// 2: Mode switching is by the CMD_MPG_ENABLE_TOGGLE (0x8B) command character.
//#define KEYPAD_ENABLE 1 // 1: uses a I2C keypad for input.
// 2: uses a serial stream for input. If MPG_ENABLE is set > 0 the serial stream is shared with the MPG.
//#define LASER_COOLANT_ENABLE 1 // Laser coolant plugin. To be completed.
//#define LB_CLUSTERS_ENABLE 1 // LaserBurn cluster support.
//#define FANS_ENABLE 1 // Enable fan control via M106/M107. Enables fans plugin.
//#define EMBROIDERY_ENABLE 1 // Embroidery plugin. To be completed.
//#define TRINAMIC_ENABLE 2130 // Trinamic TMC2130 stepper driver support. NOTE: work in progress.
//#define TRINAMIC_ENABLE 5160 // Trinamic TMC5160 stepper driver support. NOTE: work in progress.
//#define TRINAMIC_I2C 1 // Trinamic I2C - SPI bridge interface.
//#define TRINAMIC_DEV 1 // Development mode, adds a few M-codes to aid debugging. Do not enable in production code.
//#define EEPROM_ENABLE 16 // I2C EEPROM/FRAM support. Set to 16 for 2K, 32 for 4K, 64 for 8K, 128 for 16K and 256 for 16K capacity.
//#define EEPROM_IS_FRAM 1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
#define ESTOP_ENABLE 0 // When enabled only real-time report requests will be executed when the reset pin is asserted.
// NOTE: if left commented out the default setting is determined from COMPATIBILITY_LEVEL.
//#define RGB_LED_ENABLE 2 // Set to 1 to enable strip length settings $536 and $537, set to 2 to also enable M150 LED strip control.
//#define PWM_SERVO_ENABLE 1 // Enable PWM servo support, requires at least one PWM capable auxillary output.
//#define BLTOUCH_ENABLE 1 // Enable BLTouch support. Requires and claims one PWM servo output.
//#define EVENTOUT_ENABLE 1 // Enable binding events (triggers) to control auxillary outputs.
// Optional control signals:
// These will be assigned to aux input pins. Use the $pins command to check which pins are assigned.
// NOTE: If not enough pins are available assignment will silently fail.
//#define PROBE_ENABLE 0 // Uncomment to disable probe input.
//#define SAFETY_DOOR_ENABLE 1
//#define MOTOR_FAULT_ENABLE 1
//#define MOTOR_WARNING_ENABLE 1
//#define PROBE_DISCONNECT_ENABLE 1
//#define STOP_DISABLE_ENABLE 1
//#define BLOCK_DELETE_ENABLE 1
//#define SINGLE_BLOCK_ENABLE 1
//#define LIMITS_OVERRIDE_ENABLE 1
// If the selected board map supports more than three motors ganging and/or auto-squaring
// of axes can be enabled here.
//#define X_GANGED 1
//#define X_AUTO_SQUARE 1
//#define Y_GANGED 1
//#define Y_AUTO_SQUARE 1
//#define Z_GANGED 1
//#define Z_AUTO_SQUARE 1
// For ganged axes the limit switch input (if available) can be configured to act as a max travel limit switch.
// NOTE: If board map already has max limit inputs defined this configuration will be ignored.
//#define X_GANGED_LIM_MAX 1
//#define Y_GANGED_LIM_MAX 1
//#define Z_GANGED_LIM_MAX 1
//
#if WIFI_ENABLE || ETHERNET_ENABLE || WEBUI_ENABLE
#define TELNET_ENABLE 1 // Telnet daemon - requires WiFi streaming enabled.
//#define WEBSOCKET_ENABLE 1 // Websocket daemon - requires WiFi streaming enabled.
//#define MDNS_ENABLE 0 // mDNS daemon. Do NOT enable here, enable in CMakeLists.txt!
//#define SSDP_ENABLE 1 // SSDP daemon - requires HTTP enabled.
//#define MQTT_ENABLE 1 // MQTT client API, only enable if needed by plugin code.
#if SDCARD_ENABLE || WEBUI_ENABLE
#define FTP_ENABLE 1 // Ftp daemon - requires SD card enabled.
//#define HTTP_ENABLE 1 // http daemon - requires SD card enabled.
//#define WEBDAV_ENABLE 1 // webdav protocol - requires http daemon and SD card enabled.
#endif
// The following symbols have the default values as shown, uncomment and change as needed.
//#define NETWORK_STA_HOSTNAME "grblHAL"
//#define NETWORK_STA_IPMODE 1 // 0 = static, 1 = DHCP, 2 = AutoIP
//#define NETWORK_STA_IP "192.168.5.1"
//#define NETWORK_STA_GATEWAY "192.168.5.1"
//#define NETWORK_STA_MASK "255.255.255.0"
#if WIFI_SOFTAP
#define NETWORK_AP_SSID "grblHAL_AP"
#define NETWORK_AP_PASSWORD "grblHALap"
#define NETWORK_AP_HOSTNAME "grblHAL_AP"
#define NETWORK_AP_IPMODE 0 // Do not change!
#define NETWORK_AP_IP "192.168.4.1" // Do not change!
#define NETWORK_AP_GATEWAY "192.168.4.1" // Do not change!
#define NETWORK_AP_MASK "255.255.255.0"
#endif
//#define NETWORK_FTP_PORT 21
#define NETWORK_TELNET_PORT 23
//#define NETWORK_HTTP_PORT 80
#if HTTP_ENABLE
//#define NETWORK_WEBSOCKET_PORT 81
#else
//#define NETWORK_WEBSOCKET_PORT 80
#endif // HTTP_ENABLE
#endif // WIFI_ENABLE
The text was updated successfully, but these errors were encountered: