diff --git a/samples/basic/blinky/CMakeLists.txt b/samples/basic/blinky/CMakeLists.txt
index 4de34fbd81e7dc9..84e0afb794b32a3 100644
--- a/samples/basic/blinky/CMakeLists.txt
+++ b/samples/basic/blinky/CMakeLists.txt
@@ -2,6 +2,13 @@
 
 cmake_minimum_required(VERSION 3.20.0)
 find_package(Zephyr REQUIRED HINTS $ENV{ZEPHYR_BASE})
+
+if(NOT CONFIG_BOARD_NRF54L15PDK_NRF54L15_CPUAPP)
+  message(FATAL_ERROR "${BOARD} is not supported for this sample")
+endif()
+
 project(blinky)
 
 target_sources(app PRIVATE src/main.c)
+
+include(ExternalProject)
diff --git a/samples/basic/blinky/Kconfig.sysbuild b/samples/basic/blinky/Kconfig.sysbuild
new file mode 100644
index 000000000000000..70a2f7380e80b23
--- /dev/null
+++ b/samples/basic/blinky/Kconfig.sysbuild
@@ -0,0 +1,9 @@
+# Copyright 2023 Nordic Semiconductor ASA
+#
+# SPDX-License-Identifier: Apache-2.0
+
+source "share/sysbuild/Kconfig"
+
+config REMOTE_BOARD
+string
+	default "nrf54l15pdk/nrf54l15/cpuflpr" if $(BOARD) = "nrf54l15pdk"
diff --git a/samples/basic/blinky/boards/nrf54l15pdk_nrf54l15_cpuapp.overlay b/samples/basic/blinky/boards/nrf54l15pdk_nrf54l15_cpuapp.overlay
new file mode 100644
index 000000000000000..f8a0ce62b769a04
--- /dev/null
+++ b/samples/basic/blinky/boards/nrf54l15pdk_nrf54l15_cpuapp.overlay
@@ -0,0 +1,82 @@
+/*
+ * Copyright (c) 2024 Nordic Semiconductor ASA
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	soc {
+		reserved-memory {
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			sram_rx: memory@20018000 {
+				reg = <0x20018000 0x0800>;
+			};
+
+			sram_tx: memory@20020000 {
+				reg = <0x20020000 0x0800>;
+			};
+		};
+	};
+
+	ipc {
+		ipc0: ipc0 {
+			compatible = "zephyr,ipc-icmsg";
+			tx-region = <&sram_tx>;
+			rx-region = <&sram_rx>;
+			mboxes = <&cpuapp_vevif_rx 15>, <&cpuapp_vevif_tx 16>;
+			mbox-names = "rx", "tx";
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led4: led_4 {
+			gpios = <&egpio2 7 GPIO_ACTIVE_HIGH>;
+			label = "Test LED 4";
+		};
+	};
+
+	aliases {
+		led4 = &led4;
+	};
+
+	egpio2: egpio2 {
+		compatible = "nordic,nrf-egpio";
+		gpio-reserved-ranges = <0 6>, <8 4>;
+		#gpio-cells = <2>;
+		ngpios = <11>;
+		status = "okay";
+		port = <2>;
+	};
+};
+
+&cpuapp_vevif_rx {
+	status = "okay";
+};
+
+&cpuapp_vevif_tx {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "disabled";
+};
+
+&gpio1 {
+	status = "disabled";
+};
+
+&gpio2 {
+	status = "disabled";
+};
+
+&gpiote20 {
+	status = "disabled";
+};
+
+&gpiote30 {
+	status = "disabled";
+};
diff --git a/samples/basic/blinky/prj.conf b/samples/basic/blinky/prj.conf
index 91c3c15b37d1ee4..c821495d167e73e 100644
--- a/samples/basic/blinky/prj.conf
+++ b/samples/basic/blinky/prj.conf
@@ -1 +1,6 @@
 CONFIG_GPIO=y
+
+CONFIG_IPC_SERVICE=y
+CONFIG_IPC_SERVICE_BACKEND_ICMSG=y
+CONFIG_MBOX=y
+CONFIG_MULTITHREADING=n
diff --git a/samples/basic/blinky/remote/CMakeLists.txt b/samples/basic/blinky/remote/CMakeLists.txt
new file mode 100644
index 000000000000000..ec6affa1e1a00d2
--- /dev/null
+++ b/samples/basic/blinky/remote/CMakeLists.txt
@@ -0,0 +1,14 @@
+#
+# Copyright (c) 2022 Nordic Semiconductor ASA
+#
+# SPDX-License-Identifier: Apache-2.0
+#
+
+cmake_minimum_required(VERSION 3.20.0)
+
+find_package(Zephyr REQUIRED HINTS $ENV{ZEPHYR_BASE})
+project(ipc_service_remote)
+
+target_include_directories(app PRIVATE ${CMAKE_CURRENT_SOURCE_DIR}/../common)
+
+target_sources(app PRIVATE src/main.c)
diff --git a/samples/basic/blinky/remote/boards/nrf54l15pdk_nrf54l15_cpuflpr.conf b/samples/basic/blinky/remote/boards/nrf54l15pdk_nrf54l15_cpuflpr.conf
new file mode 100644
index 000000000000000..3f40e856c8812e2
--- /dev/null
+++ b/samples/basic/blinky/remote/boards/nrf54l15pdk_nrf54l15_cpuflpr.conf
@@ -0,0 +1 @@
+CONFIG_MULTITHREADING=n
diff --git a/samples/basic/blinky/remote/boards/nrf54l15pdk_nrf54l15_cpuflpr.overlay b/samples/basic/blinky/remote/boards/nrf54l15pdk_nrf54l15_cpuflpr.overlay
new file mode 100644
index 000000000000000..f87d164072a7f71
--- /dev/null
+++ b/samples/basic/blinky/remote/boards/nrf54l15pdk_nrf54l15_cpuflpr.overlay
@@ -0,0 +1,61 @@
+/*
+ * Copyright (c) 2024 Nordic Semiconductor ASA
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	soc {
+		reserved-memory {
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			sram_tx: memory@20018000 {
+				reg = <0x20018000 0x0800>;
+			};
+
+			sram_rx: memory@20020000 {
+				reg = <0x20020000 0x0800>;
+			};
+		};
+	};
+
+	ipc {
+		ipc0: ipc0 {
+			compatible = "zephyr,ipc-icmsg";
+			tx-region = <&sram_tx>;
+			rx-region = <&sram_rx>;
+			mboxes = <&cpuflpr_vevif_rx 16>, <&cpuflpr_vevif_tx 15>;
+			mbox-names = "rx", "tx";
+			status = "okay";
+		};
+	};
+};
+
+&cpuflpr_vevif_rx {
+	status = "okay";
+};
+
+&cpuflpr_vevif_tx {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "disabled";
+};
+
+&gpio1 {
+	status = "disabled";
+};
+
+&gpio2 {
+	status = "disabled";
+};
+
+&gpiote20 {
+	status = "disabled";
+};
+
+&gpiote30 {
+	status = "disabled";
+};
diff --git a/samples/basic/blinky/remote/prj.conf b/samples/basic/blinky/remote/prj.conf
new file mode 100644
index 000000000000000..530e6ab86604200
--- /dev/null
+++ b/samples/basic/blinky/remote/prj.conf
@@ -0,0 +1,3 @@
+CONFIG_IPC_SERVICE=y
+CONFIG_IPC_SERVICE_BACKEND_ICMSG=y
+CONFIG_MBOX=y
diff --git a/samples/basic/blinky/remote/src/main.c b/samples/basic/blinky/remote/src/main.c
new file mode 100644
index 000000000000000..0b75cf6e12a2c93
--- /dev/null
+++ b/samples/basic/blinky/remote/src/main.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright (c) 2016 Intel Corporation
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+#ifdef CONFIG_MULTITHREADING
+#include <zephyr/kernel.h>
+#endif
+#include <stdio.h>
+#include <zephyr/drivers/gpio.h>
+#include <zephyr/dt-bindings/gpio/nordic-nrf-gpio.h>
+#include <zephyr/ipc/ipc_service.h>
+
+#include <hal/nrf_vpr_csr.h>
+#include <hal/nrf_vpr_csr_vio.h>
+#include <haly/nrfy_gpio.h>
+#include <nrfe_gpio.h>
+
+static struct ipc_ept ep;
+
+#ifdef CONFIG_MULTITHREADING
+K_SEM_DEFINE(bound_sem, 0, 1);
+#else
+volatile uint32_t bound_sem = 1;
+#endif
+
+static void ep_bound(void *priv)
+{
+#ifdef CONFIG_MULTITHREADING
+	k_sem_give(&bound_sem);
+#else
+	bound_sem = 0;
+#endif
+	printf("Ep bounded\n");
+}
+
+static nrf_gpio_pin_pull_t get_pull(gpio_flags_t flags)
+{
+	if (flags & GPIO_PULL_UP) {
+		return NRF_GPIO_PIN_PULLUP;
+	} else if (flags & GPIO_PULL_DOWN) {
+		return NRF_GPIO_PIN_PULLDOWN;
+	}
+
+	return NRF_GPIO_PIN_NOPULL;
+}
+
+static int gpio_nrfe_pin_configure(uint8_t port, uint16_t pin, uint32_t flags)
+{
+	__ASSERT(port == 2, "Invalid port. Only port 2 is supported");
+
+	uint32_t abs_pin = NRF_GPIO_PIN_MAP(port, pin);
+	nrf_gpio_pin_pull_t pull = get_pull(flags);
+	nrf_gpio_pin_drive_t drive;
+
+	switch (flags & (NRF_GPIO_DRIVE_MSK | GPIO_OPEN_DRAIN)) {
+	case NRF_GPIO_DRIVE_S0S1:
+		drive = NRF_GPIO_PIN_S0S1;
+		break;
+	case NRF_GPIO_DRIVE_S0H1:
+		drive = NRF_GPIO_PIN_S0H1;
+		break;
+	case NRF_GPIO_DRIVE_H0S1:
+		drive = NRF_GPIO_PIN_H0S1;
+		break;
+	case NRF_GPIO_DRIVE_H0H1:
+		drive = NRF_GPIO_PIN_H0H1;
+		break;
+	case NRF_GPIO_DRIVE_S0 | GPIO_OPEN_DRAIN:
+		drive = NRF_GPIO_PIN_S0D1;
+		break;
+	case NRF_GPIO_DRIVE_H0 | GPIO_OPEN_DRAIN:
+		drive = NRF_GPIO_PIN_H0D1;
+		break;
+	case NRF_GPIO_DRIVE_S1 | GPIO_OPEN_SOURCE:
+		drive = NRF_GPIO_PIN_D0S1;
+		break;
+	case NRF_GPIO_DRIVE_H1 | GPIO_OPEN_SOURCE:
+		drive = NRF_GPIO_PIN_D0H1;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (flags & GPIO_OUTPUT_INIT_HIGH) {
+		uint16_t outs = nrf_vpr_csr_vio_out_get();
+
+		nrf_vpr_csr_vio_out_set(outs | (BIT(pin)));
+	} else if (flags & GPIO_OUTPUT_INIT_LOW) {
+		uint16_t outs = nrf_vpr_csr_vio_out_get();
+
+		nrf_vpr_csr_vio_out_set(outs & ~(BIT(pin)));
+	}
+
+	nrf_gpio_pin_dir_t dir =
+		(flags & GPIO_OUTPUT) ? NRF_GPIO_PIN_DIR_OUTPUT : NRF_GPIO_PIN_DIR_INPUT;
+	nrf_gpio_pin_input_t input =
+		(flags & GPIO_INPUT) ? NRF_GPIO_PIN_INPUT_CONNECT : NRF_GPIO_PIN_INPUT_DISCONNECT;
+
+	/* Reconfigure the GPIO pin with the specified pull-up/pull-down configuration and drive
+	 * strength.
+	 */
+	nrfy_gpio_reconfigure(abs_pin, &dir, &input, &pull, &drive, NULL);
+
+	if (dir == NRF_GPIO_PIN_DIR_OUTPUT) {
+		nrf_vpr_csr_vio_dir_set(nrf_vpr_csr_vio_dir_get() | (BIT(pin)));
+	}
+
+	/* Take control of the pin */
+	nrfy_gpio_pin_control_select(abs_pin, NRF_GPIO_PIN_SEL_VPR);
+
+	return 0;
+}
+
+static void gpio_nrfe_port_set_bits_raw(uint16_t set_mask)
+{
+	uint16_t outs = nrf_vpr_csr_vio_out_get();
+
+	nrf_vpr_csr_vio_out_set(outs | set_mask);
+}
+
+static void gpio_nrfe_port_clear_bits_raw(uint16_t clear_mask)
+{
+	uint16_t outs = nrf_vpr_csr_vio_out_get();
+
+	nrf_vpr_csr_vio_out_set(outs & ~clear_mask);
+}
+
+static void gpio_nrfe_port_toggle_bits(uint16_t toggle_mask)
+{
+	nrf_vpr_csr_vio_out_toggle_set(toggle_mask);
+}
+
+static void ep_recv(const void *data, size_t len, void *priv)
+{
+	nrfe_gpio_data_packet_t *packet = (nrfe_gpio_data_packet_t *)data;
+
+	switch (packet->opcode) {
+	case NRFE_GPIO_PIN_CONFIGURE: {
+		printf("Configuring GPIO%d pin: %d\n", packet->port, packet->pin);
+		gpio_nrfe_pin_configure(packet->port, packet->pin, packet->flags);
+		break;
+	}
+	case NRFE_GPIO_PIN_CLEAR: {
+		printf("Clearing GPIO%d, pin 0x%04x\n", packet->port, packet->pin);
+		gpio_nrfe_port_clear_bits_raw(packet->pin);
+		break;
+	}
+	case NRFE_GPIO_PIN_SET: {
+		printf("Setting GPIO%d, pin 0x%04x\n", packet->port, packet->pin);
+		gpio_nrfe_port_set_bits_raw(packet->pin);
+		break;
+	}
+	case NRFE_GPIO_PIN_TOGGLE: {
+		printf("Toggling GPIO%d, pin 0x%04x\n", packet->port, packet->pin);
+		gpio_nrfe_port_toggle_bits(packet->pin);
+		break;
+	}
+	default: {
+		printf("Unknown opcode %d\n", packet->opcode);
+		break;
+	}
+	}
+}
+
+static struct ipc_ept_cfg ep_cfg = {
+	.cb = {
+		.bound = ep_bound,
+		.received = ep_recv,
+	},
+};
+
+int main(void)
+{
+	int ret;
+	const struct device *ipc0_instance;
+
+	ipc0_instance = DEVICE_DT_GET(DT_NODELABEL(ipc0));
+
+	ret = ipc_service_open_instance(ipc0_instance);
+	if ((ret < 0) && (ret != -EALREADY)) {
+		printf("ipc_service_open_instance() failure\n");
+		return ret;
+	}
+
+	ret = ipc_service_register_endpoint(ipc0_instance, &ep, &ep_cfg);
+	if (ret < 0) {
+		printf("ipc_service_register_endpoint() failure\n");
+		return ret;
+	}
+
+	/* Wait for endpoint to be bound */
+#ifdef CONFIG_MULTITHREADING
+	k_sem_take(&bound_sem, K_FOREVER);
+#else
+	while (bound_sem != 0) {
+	};
+#endif
+
+	if (!nrf_vpr_csr_rtperiph_enable_check()) {
+		nrf_vpr_csr_rtperiph_enable_set(true);
+	}
+
+	while (true) {
+	};
+
+	return 0;
+}
diff --git a/samples/basic/blinky/sample.yaml b/samples/basic/blinky/sample.yaml
index de711910dad24d8..43996dbdbd12ffb 100644
--- a/samples/basic/blinky/sample.yaml
+++ b/samples/basic/blinky/sample.yaml
@@ -10,3 +10,22 @@ tests:
     harness: led
     integration_platforms:
       - frdm_k64f
+
+  sample.basic.blinky.egpio:
+    tags:
+      - LED
+      - gpio
+      - ipc
+    filter: dt_enabled_alias_with_parent_compat("led0", "gpio-leds")
+    depends_on: gpio
+    harness:
+      - remote
+      - led
+    platform_allow: nrf54l15pdk/nrf54l15/cpuapp
+    integration_platforms:
+      - nrf54l15pdk/nrf54l15/cpuapp
+    extra_args:
+      blinky_SNIPPET=nordic-flpr
+      blinky_CONFIG_MULTITHREADING=n
+      remote_CONFIG_MULTITHREADING=n
+    sysbuild: true
diff --git a/samples/basic/blinky/src/main.c b/samples/basic/blinky/src/main.c
index 4cab4969d94b5fc..cfc32ab727d6d3e 100644
--- a/samples/basic/blinky/src/main.c
+++ b/samples/basic/blinky/src/main.c
@@ -9,10 +9,10 @@
 #include <zephyr/drivers/gpio.h>
 
 /* 1000 msec = 1 sec */
-#define SLEEP_TIME_MS   1000
+#define SLEEP_TIME_MS 1000
 
 /* The devicetree node identifier for the "led0" alias. */
-#define LED0_NODE DT_ALIAS(led0)
+#define LED0_NODE DT_ALIAS(led4)
 
 /*
  * A build error on this line means your board is unsupported.
@@ -25,6 +25,8 @@ int main(void)
 	int ret;
 	bool led_state = true;
 
+	k_busy_wait(SLEEP_TIME_MS * 100);
+
 	if (!gpio_is_ready_dt(&led)) {
 		return 0;
 	}
@@ -42,7 +44,11 @@ int main(void)
 
 		led_state = !led_state;
 		printf("LED state: %s\n", led_state ? "ON" : "OFF");
+#ifdef CONFIG_MULTITHREADING
 		k_msleep(SLEEP_TIME_MS);
+#else
+		k_busy_wait(SLEEP_TIME_MS * 1000);
+#endif
 	}
 	return 0;
 }
diff --git a/samples/basic/blinky/sysbuild.cmake b/samples/basic/blinky/sysbuild.cmake
new file mode 100644
index 000000000000000..62c9e931d60f11b
--- /dev/null
+++ b/samples/basic/blinky/sysbuild.cmake
@@ -0,0 +1,14 @@
+# Copyright (c) 2024 Nordic Semiconductor ASA
+# SPDX-License-Identifier: Apache-2.0
+
+if ("${SB_CONFIG_REMOTE_BOARD}" STREQUAL "")
+	message(FATAL_ERROR
+	"Target ${BOARD} not supported for this sample. "
+	"There is no remote board selected in Kconfig.sysbuild")
+endif()
+
+ExternalZephyrProject_Add(
+	APPLICATION remote
+	SOURCE_DIR  ${APP_DIR}/remote
+	BOARD       ${SB_CONFIG_REMOTE_BOARD}
+)