-
Notifications
You must be signed in to change notification settings - Fork 1
/
README.NETWORKING
416 lines (290 loc) · 15.8 KB
/
README.NETWORKING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
-----------------------------------------------------------------
Hercules Networking
-----------------------------------------------------------------
*** Please read herctcp.html as Roger explains how ***
*** to set up TCP/IP networking with Hercules. ***
All of the communications emulation implemented within Hercules
use a CTCA (Channel to Channel Adapter) type device. Depending on
the "flavor", the CTCA device will provide either a
point-to-point or a virtual network adapter interface to the
driving system's TCP/IP stack or in the case of CTCT, a "true"
CTCA connection to another instance of Hercules via a TCP/IP
connection.
All current emulations, with the exception of VMNET, CTCT and CTCE use
the Universal TUN/TAP driver on *nix and TunTap32 (WinPCap) on
the Windows platforms which creates a network interface on the
driving system which allow Hercules to present frames to, and
receive frames from the TCP/IP stack. This network interface is
configured on *nix platforms by the hercifc program which is
invoked by Hercules after the TUN/TAP device is opened. The
hercifc program runs as root. Please read herctcp.html for more
information on the security implications of the hercifc program.
Now for the gory details:
---------------------------------------------------------------
*** Important information about changes to the ***
*** Hercules configuration files - PLEASE READ ***
The format of the Hercules configuration file statements for all
of the networking emulations have changed from the previous
releases of Hercules. The older format will still be accepted
to maintain compatibility, however it is the recommendation
of the maintainer that the new format be used. Also note that
there is no distinction between the CTCI and CTCI-W32 modes any
more, in fact CTCI-W32 does not exist in this release (other
than to maintain compatibility with previous configuration files).
---------------------------------------------------------------
*** Important information about changes to the ***
*** Hercules configuration files - PLEASE READ ***
In releases prior to Hercules version 3.00, all of the TCP/IP
emulations required two addresses to be defined in the Hercules
configuration file: one address for the read subchannel and the
other for write.
---------------------------------------------------------------
*** Important information about changes to the ***
*** Hercules configuration files - PLEASE READ ***
Hercules release version 3.00, however, [temporarily] changed
the rules: With [ONLY!] version 3.00 of Hercules, only the FIRST
address address need be specified in the configuration file.
Hercules version 3.00 automatically creates the second address.
Care must be taken to NOT define the second address [with Hercules
version 3.00 ONLY!] or a configuration error will occur.
---------------------------------------------------------------
*** Important information about changes to the ***
*** Hercules configuration files - PLEASE READ ***
Starting with Hercules version 3.01 however, we've gone back to
doing things the way we ORIGINALLY were (and the way most users
are used to (i.e. the way most users EXPECT things to work)):
With Hercules version 3.01 you need to define BOTH addresses!
Both the even numbered read device AS WELL AS the odd numbered
write device must BOTH be defined in your Hercules configuration
file starting with Hercules version 3.01. We apologize for the
mess, but we thought having Herc automatically define the write
device for you (as it does in version 3.00) would be easier for
everyone. Turns out it caused a lot of problems with a lot of
people, so we decided to go back to the original way. Again, we
apologize for whatever headaches this may have caused anyone.
---------------------------------------------------------------
*** Important information about changes to the ***
*** Hercules configuration files - PLEASE READ ***
Note that the VMNET and CTCT protocols have ALWAYS required BOTH
addresses to be defined (i.e. ALL versions of Hercules, including
version 3.00 as well, require BOTH even/odd read/write devices to
be defined separately [in your Hercules configuration file]).
---------------------------------------------------------------
The currently supported emulation modes are:
CTCT - CTCA Emulation via TCP connection
CTCE - Enhanced CTCA Emulation via CTP connection
CTCI - Point-to-point connection to the host IP stack.
LCS - LAN Channel Station (3172/OSA)
VMNET - Point-to-point link via SLIP/VMNET
-----------------------------------------------------------------
CTCT - Channel to Channel Emulation via TCP connection
-----------------------------------------------------------------
This emulation mode provides protocol-independent communication
with another instance of this driver via a TCP connection.
This mode appears to the operating system running in the Hercules
machine as an IBM 3088 Channel to Channel Adapter and can operate
in either Basic or Extended mode.
The configuration statement for CTCT is as follows:
<devnum> 3088 CTCT <lport> <raddress> <rport> <mtu>
where:
<devnum> is the address of the CTCT device.
<lport> is the TCP/IP port on the local system.
<raddress> is the IP address on the remote.
<rport> is the TCP/IP port on the remote system.
-----------------------------------------------------------------
CTCI - Channel to Channel link to Linux TCP/IP stack
-----------------------------------------------------------------
This is a point-to-point link to the driving system's TCP/IP
stack. From the point of view of the operating system running
in the Hercules machine it appears to be a CTC link to a machine
running TCP/IP for MVS or VM.
CTCI uses the Universal TUN/TAP driver on *nix and Politecnico
di Torino's WinPCap packet driver as well as Fish's TunTap32
and FishPack DLLs on Windows[1].
The configuration statement for CTCI is as follows:
<devnum1-devnum2> CTCI [options] <guestip> <hostip>
where:
<devnum1-devnum2> is the address pair of the CTCI device.
<guestip> is the IP address of the Hercules (guest OS) side.
<hostip> is the IP address on the driving system.
[options] can be any of the following:
-n <devname> or --dev <devname>
where <devname> is:
[*nix] the name of the TUN/TAP special character
device, normally /dev/net/tun.
[Windows] is either the IP or MAC address of the
driving systems network card. TunTap32 will
automatically select the first network card it
finds if this option is omitted, this may not be
desirable for some users.
-t <mtu> or --mtu <mtu>
[*nix only] where <mtu> is the maximum transmission
unit size, normally 1500
-s <netmask> or --netmask <netmask>
[*nix only] where <netmask> is the netmask to
be configured on the link. Note: Since this is a
point-to-point link netmask is meaningless from
the perspective of the actual network device.
-m <MAC Address> or --mac <MAC address>
[Windows only] where <MAC Address> is the optional
hardware address of the interface in the format of
either xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
-k <kbuff> or --kbuff <kbuff>
[Windows only] where <kbuff> is the size of the
WinPCap kernel buffer size, normally 1024.
-i <ibuff> or --ibuff <ibuff>
[Windows only] where <ibuff> is the size of the
WinPCap I/O buffer size, normally 64.
-d or --debug
this will turn on the internal debugging routines.
Warning: This will produce a tremendous amount of
output to the Hercules console. It is suggested that
you only enable this at the request of the maintainers.
-----------------------------------------------------------------
LCS - LAN Channel Station
-----------------------------------------------------------------
This emulation mode appears to the operating system running in
the Hercules machine as an IBM 8232 LCS device, an IBM 2216
router, a 3172 running ICP (Interconnect Communications Program),
the LCS3172 driver of a P/390, or an IBM Open Systems Adapter.
Rather than a point-to-point link, this emulation creates a
virtual ethernet adapter through which the guest operating system
running in the Hercules machine can communicate. As such, this
mode is not limited to TCP/IP traffic, but in fact will handle
any ethernet frame.
The configuration statement for LCS is as follows:
<devnum1-devnum2> LCS [options] [<guestip>]
where:
<devnum1-devnum2> is the address pair of the LCS device.
This pair must be an even-odd address.
[<guestip>] is an optional IP address of the Hercules
(guest OS) side. Note: This is only used to
establish a point-to-point routing table entry
on driving system. If you use the --oat option,
do not specify an address here.
There are no required parameters for the LCS emulation, however
there are several options that can be specified on the config
statement:
-n <devname> or --dev <devname>
where <devname> is:
[*nix] the name of the TUN/TAP special character device,
normally /dev/net/tun.
[Windows] is either the IP or MAC address of the driving
systems network card. TunTap32 will automatically select
the first network card it finds if this option is
omitted, this may not be desirable for some users.
-o <filename> or --oat <filename>
where <filename> specifies the filename of the Address
Translation file. If this option is specified, the optional
<guestip> and --mac entries are ignored in preference to
statements in the OAT. (See below for the format of the OAT)
-m <MAC Address> or --mac <MAC address>
where <MAC Address> is the optional hardware address of
the interface in the format: xx:xx:xx:xx:xx:xx
-d or --debug
this will turn on the internal debugging routines.
Warning: This will produce a tremendous amount of
output to the Hercules console. It is suggested that
you only enable this at the request of the maintainers.
If no Address Translation file is specified, the emulation module
will create the following:
An ethernet adapter (port 0) for TCP/IP traffic only.
Two device addresses will be defined (devnum and devnum + 1).
The syntax for the Address Translation file is as follows:
*********************************************************
* Dev Mode Port Entry specific information *
*********************************************************
0400 IP 00 PRI 172.021.003.032
0402 IP 00 SEC 172.021.003.033
0404 IP 00 NO 172.021.003.038
0406 IP 01 NO 172.021.002.016
040E SNA 00
HWADD 00 02:00:FE:DF:00:42
HWADD 01 02:00:FE:DF:00:43
ROUTE 00 172.021.003.032 255.255.255.224
where:
Dev is the base device address
Mode is the operation mode - IP or SNA
Port is the virtual (relative) adapter number.
When the device is specifies the odd address of the pair,
then the read/write functions of the pair will be swapped.
For IP modes, the entry specific information is as follows:
PRI|SEC|NO specifies where a packet with an unknown IP
address is forwarded to. PRI is the primary
default entry, SEC specifies the entry to use
when the primary is not available, and NO
specifies that this is not a default entry.
nnn.nnn.nnn.nnn specifies the home IP address
When the operation mode is IP, specify only the even (read)
address. The odd (write) address will be create automatically.
Note: SNA mode does not currently work.
Additionally, two other statements can be included in the
address translation file. The HWADD and ROUTE statements.
Use the HWADD to specify a hardware (MAC) address for a
virtual adapter. The first parameter after HWADD specifies
with relative adapter for which the address is applied.
The ROUTE statement is included for convenience. This allows the
hercifc program to create a network route for this specified
virtual adapter. Please note that it is not necessary to include
point-to-point routes for each IP address in the table. This is
done automatically by the emulation module.
Up to 4 virtual (relative) adapters 00-03 are currently supported.
-----------------------------------------------------------------
SLIP/VMNET - Channel to Channel link to TCP/IP via SLIP/VMNET
-----------------------------------------------------------------
If the emulation mode is not specified on the configuration
statement, it is assumed to be a point-to-point link to the
driving system's TCP/IP stack using Willem Konynenberg's VMNET
package. This provides the same function as the CTCI mode of
operation, except that it uses a virtual SLIP interface instead
of the TUN/TAP driver.
Refer to http://www.kiyoinc.com/herc3088.html for more details.
-----------------------------------------------------------------
CTCE - Enhanced Channel to Channel Emulation via TCP connection
-----------------------------------------------------------------
The CTCE device type will emulate a real 3088 Channel to Channnel
Adapter also for non-IP traffic, enhancing the CTCT capabilities.
CTCE connections are also based on TCP/IP between two (or more)
Hercules instances, and requires an even-odd pair of port numbers
per device side. Only the even port numbers are to be configured;
the odd numbers are just derived by adding 1 to the (configured)
even port numbers. The socket connection pairs cross-connect,
the arrows showing the send->receive direction :
x-lport-even -> y-rport-odd
x-lport-odd <- y-rport-even
The configuration statement for CTCE is as follows :
<devnum> CTCE <lport> <raddress> <rport> [[<mtu>] <sml>]
where:
<devnum> is the address of the CTCT device.
<lport> is the even TCP/IP port on the local system.
<raddress> is the IP address on the remote.
<rport> is the even TCP/IP port on the remote system.
<mtu> optional mtu buffersize, defaults to 32778
<sml> optional small minimum for mtu, defaults to 8
A sample CTCE device configuration is shown below:
Hercules PC Host A with IP address 192.168.1.100 :
0E40 CTCE 30880 192.168.1.200 30880
0E41 CTCE 30882 192.168.1.200 30882
Hercules PC Host B with IP address 192.168.1.200 :
0E40 CTCE 30880 192.168.1.100 30880
0E41 CTCE 30882 192.168.1.100 30882
CTCE connected Hercules instances can be hosted on either Unix
or Windows platforms, both sides do not need to be the same.
=================================================================
[1] The TunTap32.dll and FishPack.dll are part of Fish's CTCI-W32
http://www.softdevlabs.com/Hercules/ctci-w32-index.html
package, but the required WinPCap packet driver must be installed
separately from http://www.winpcap.org See Fish's web page for
details.
ALSO NOTE that it is HIGHLY RECOMMENDED that you stick with using
only the current RELEASE version of WinPCap and NOT any type of
'alpha' OR 'beta' version! Alpha and Beta versions of WinPCap are
NOT SUPPORTED! Only official *release* version are supported!
When you visit the WinPCap download web page, you need need to
scroll down the page a bit to reach the OFFICIAL RELEASE VERSION
of WinPcap. They usually put their Beta versions at the top of the
page, and BETA versions ARE NOT SUPPORTED. *Please* scroll down
the page and use and official RELEASE version. Thanks.
You may, if you want, use a beta version of WinPCap, but if you do,
then you're on your own if you have any problems with it.
-- Fish, May 2004.