OTA

Over-the-air updates

ESPurna offers several ways to upgrade an ESPurna device over-the-air:

• Manually driven OTA updates (from PlatformIO or Arduino IDE)
• Web interface updates (uploading a binary image from the web UI)
• Terminal updates (connecting via serial or telnet and providing a URL of an image)
• HTTP updates (POSTing a binary image to the device)
• Automatic OTA updates (using the NoFUSS library, not supported by default)

Manually driven OTA updates

Once you have flashed your board with the ESPurna firmware you can flash it again over-the-air using PlatformIO and the ota environment:

$ pio run -t upload -e itead-sonoff-basic-ota

When using OTA environment it defaults to the IP address 192.168.4.1 (device IP in SoftAP mode) and fibonacci as password. If you want to flash it when connected to your home network or use different password, you must set ESPURNA_IP and ESPRUNA_AUTH environment variables:

$ export ESPURNA_IP=192.168.1.11
$ export ESPURNA_AUTH=somepassword
$ pio run -t upload -e itead-sonoff-basic-ota

Or, on Windows:

C:\espurna\code> set ESPURNA_IP=192.168.1.11
C:\espurna\code> set ESPURNA_AUTH=somepassword
C:\espurna\code> pio run -t upload -e itead-sonoff-basic-ota

Starting with version 1.9.0 the platformio.ini file defines 3 useful environments for custom OTA updates: esp8266-1m-ota, esp8266-4m-ota and esp8285-1m-ota. And example of use is:

$ export ESPURNA_IP=192.168.1.11
$ export ESPURNA_AUTH=somepassword
$ export ESPURNA_BOARD="ITEAD_SONOFF_BASIC"
$ export ESPURNA_FLAGS="-DDHT_SUPPORT=1"
$ pio run -t upload -e esp8266-1m-ota

See code/espurna/config/hardware.h for possible ESPURNA_BOARD values.

Troubleshooting

Sometimes OTA updates fail. It happens. It's not a problem since the firmware does not get overwritten if the upload fails. But if you cannot update the device firmware even after several attempts, you might try to check if you have a firewall and disable it.

Using espota.py

If platformio was used at least once to build ESPurna, espota.py can be found inside arduino framework directory:

~/.platformio/packages/framework-arduinoespressif8266/tools/espota.py
~/.platformio/packages/[email protected]/tools/espota.py
etc.

or OTA script can be fetched directly.

It does require existing firmware .bin file. Example using file from Releases:

$ python espota.py --progress --ip 192.168.4.1 --auth fibonacci --file espurna-<version>-itead-sonoff-basic.bin

Web interface updates

You can directly upload the firmware file (.bin extension) to the device using the "Upgrade" option in the "Admin" tab of the web interface. You can find the latest firmware images for your device in the releases page.

Updating from the Terminal

From version 1.12.4, ESPurna includes an 'ota' command in the terminal that allows you to update the firmware in the device passing the URL of a binary as an argument. The URL can be in the local network or the internet, but the device has to have direct access to that resource (no redirects). HTTPS is not supported at the moment.

Simply open a telnet session to the device and request an OTA update passing the URL:

$ telnet 192.168.1.15
ota http://192.168.1.11/espurna-1.12.4a-wemos-d1mini-relayshield.bin
[038771] +OK
[038771] [OTA] Downloading from 'http://192.168.1.11/espurna-1.12.4a-wemos-d1mini-relayshield.bin'
[053298] [OTA] Done, restarting...

Updating via HTTP

You can use the "/upgrade" endpoint to automate upgrades via HTTP using cURL or similar tools. This is the same endpoint that uses the web interface upgrade utility so you will need a device with ESPurna compiled with WEB_SUPPORT (this is the default).

$ curl -XPOST --digest -uadmin:<password> \
  -H "Content-Type: multipart/form-data" \
  -F "filename=@<path_to_binary>" \
  http://<ip_device>/upgrade

You will have to replace <password>, <path_to_binary> and <ip_device> with proper values for your device. For instance:

$ curl -XPOST --digest -uadmin:fibonacci \
  -H "Content-Type: multipart/form-data" \
  -F "[email protected]/esp8266-1m-ota/firmware.bin" \
  http://192.168.4.1/upgrade

Please note the '@' before the path to the binary file. The path can be relative to the current directory. The backslashes in a bash console mean that the command continues in the next line, you can write the full curl command in a single line if you want.

Thanks to FlorianSW for this tip, check the #745 for the original suggestion.

Automatic OTA updates

You can also use the automatic OTA update feature. Check the NoFUSS library for more info.

This options is disabled by default. Enable it in your firmware setting NOFUSS_SUPPORT=1 in code/espurna/config/general.h or via additional build flag (-DNOFUSS_SUPPORT=1)