gadget

🔦

Very tentative design. Sort of minimum viable design to prototype handheld interactions.

Open-back until it's more stable (sometimes you want to replug the projector, sometimes you want to plug in a USB keyboard to manually reconfigure if it's off Wi-Fi)

Bill of materials

3D prints

• Gadget chassis
  • This prints in 2 parts: Chassis and front panel
    • (for front panel, should choose either Ultimems version with smaller projector slit, or Nebra version with larger slit [since the Nebra is shifted a little toward the side])
• Handle grip with trigger button (in vendor/)
  • This prints in 3 parts so far: Main grip, thumbwheel, block
  • (Trigger inset itself is TODO)

(can view in https://3dviewer.net -- for the gadget chassis, the Gadget.shapr file is canonical / used to edit in Shapr3D, the derived files are generated from it)

Electronics

• Ultimems HD305D1-C1 (manual) (recommended) or Nebra AnyBeam (should fit)
  • There is a newer Ultimems unit HD309D1-C1 which I haven't tested yet
• Raspberry Pi 5 2GB or more
  • (only the Pi 5 is guaranteed to supply the 5V1.1A over USB port to power the projector)
  • Pi 5 active cooler (fan)
  • microSD card
  • 27W Pi 5 USB-C power supply
    • (you cannot use an off-the-shelf USB-C power supply; you must use this one)
    • TODO: battery system
• Raspberry Pi Camera 3 Wide (maybe can also be NoIR version)
  • 15cm 15-pin-to-22-pin "Pi Zero Camera Cable" (special, not the one that comes with camera -- Pi 5 has narrower MIPI ports)
    • 

Cables

• USB-C male-to-female 180-degree angle adapter
  • 
• 20cm USB-C male-to-female extension cable with panel-mount screw hole
  • 
• 7.5cm 65W USB-C Type C to USB-C Ultra Slim Flat Power USB2.0 Data Angled Cable
  • (to power projector from Pi)
  • 
  • USB-A plug to USB-C jack microadapter to fit in Pi USB port
    • 
• short microhdmi to hdmi ribbon cable:
  • 20cm HDMI ribbon cable (15cm might also work?)
    • 
  • HDMI type-A male connector up-angled 90 degree
    • 
  • micro-HDMI type-D male connector up-angled 90 degree
    • 

Other

• 4x 6mm M2 bolts (for mounting camera to front panel)
• 4x M2 nylock nuts (for mounting camera to front panel)
  • 
• 8x M2.5 bolts for Pi 5 <-> standoffs <-> chassis
• 4x M2.5 standoffs for Pi 5
• 2x M2.5 bolts for front panel
  • 2x M2.5 heat set inserts for front (to bolt front panel onto)
• 1x 1/4" bolt for top
• 1x 1/4" 6mm x 8mm heat set insert for bottom

Software setup

Flash Raspberry Pi OS Lite (64-bit).

Add to boot/config.txt on the SD card:

# For Ultimems projector:
hdmi_force_hotplug=1
hdmi_drive=2
config_hdmi_boost=4
hdmi_group=2
hdmi_mode=14
#hdmi_safe=1

Boot the Pi. Ssh in and follow Folk README setup instructions.

Use apt to install libcamera0.3 and libcamera-dev.

Use sudo nmtui to add more Wi-Fi networks.

Create ~/folk-live/setup.folk to set the camera to use wide-angle resolution and to create moving dashed outline around the perimeter of the projection:

Assert $this wishes $::thisNode uses camera "/base/axi/pcie@120000/rp1/i2c@88000/imx708@1a" with width 1280 height 1024

Assert $this wishes $::thisNode uses display 0

When display /disp/ has width /w/ height /h/ {
  When the clock time is /t/ {
    Wish to draw a dashed stroke with points [list [list 0 0] [list $w 0] [list $w $h] [list 0 $h] [list 0 0]] color white width 10 dashlength 40 dashoffset [expr {fmod($t, 10)*-120}]
  }
}

(the camera path may be different, Folk will print all valid camera paths in its journal at boot if you need to check: sudo journalctl -u folk -n 30)