Skip to content

a fork with intended new features to the solderparty bbq20kbd

License

Notifications You must be signed in to change notification settings

adrlau/bbq20kbd

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

15 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

I2C Puppet

This is a port of the old BB Q10 Keyboard-to-I2C Software to the RP2040, expanded with new features, while still staying backwards compatible.

The target product/keyboard for this software is the BB Q20 keyboard, which adds a trackpad to the mix.

On the features side, this software adds USB support, the keyboard acts as a USB keyboard, and the trackpad acts as a USB mouse.

On the I2C side, you can access the key presses, the trackpad state, you can control some of the board GPIOs, as well as the backlight.

See Protocol for details of the I2C puppet.

Checkout

The code depends on the Raspberry Pi Pico SDK, which is added as a submodule. Because the Pico SDK includes TinyUSB as a module, it is not recommended to do a recursive submodule init, and rather follow these steps:

git clone https://github.com/solderparty/i2c_puppet
cd i2c_puppet
git submodule update --init
cd 3rdparty/pico-sdk
git submodule update --init

Build

See the boards directory for a list of available boards.

mkdir build
cd build
cmake -DPICO_BOARD=bbq20kbd_breakout -DCMAKE_BUILD_TYPE=Debug ..
make

Vendor USB Class

You can configure the software over USB in a similar way you would do it over I2C. You can access the same registers (like the backlight register) using the USB Vendor Class. If you don't want to prefix all config interactions with sudo, you can copy the included udev rule:

sudo cp etc/99-i2c_puppet.rules /lib/udev/rules.d/
sudo udevadm control --reload
sudo udevadm trigger

To interact with the internal registers of the keyboard over USB, use the i2c_puppet.py script included in the etc folder. just import it, create a I2C_Puppet object, and you can interact with the keyboard in the same you would do using the I2C interface and the CircuitPython class linked below.

Implementations

Here are libraries that allow I2C interaction with the boards running this software. Not all libraries might support all the features.

Protocol

The device uses I2C slave interface to communicate, the address can be configured in app/config/conf_app.h, the default is 0x1F.

You can read the values of all the registers, the number of returned bytes depends on the register. It's also possible to write to the registers, to do that, apply the write mask 0x80 to the register ID (for example, the backlight register 0x05 becomes 0x85).

The FW Version register (REG_VER = 0x01)

Data written to this register is discarded. Reading this register returns 1 byte, the first nibble contains the major version and the second nibble contains the minor version of the firmware.

The configuration register (REG_CFG = 0x02)

This register can be read and written to, it's 1 byte in size.

This register is a bit map of various settings that can be changed to customize the behaviour of the firmware.

See REG_CF2 for additional settings.

Bit Name Description
7 CFG_USE_MODS Should Alt, Sym and the Shift keys modify the keys being reported.
6 CFG_REPORT_MODS Should Alt, Sym and the Shift keys be reported as well.
5 CFG_PANIC_INT Currently not implemented.
4 CFG_KEY_INT Should an interrupt be generated when a key is pressed.
3 CFG_NUMLOCK_INT Should an interrupt be generated when Num Lock is toggled.
2 CFG_CAPSLOCK_INT Should an interrupt be generated when Caps Lock is toggled.
1 CFG_OVERFLOW_INT Should an interrupt be generated when a FIFO overflow happens.
0 CFG_OVERFLOW_ON When a FIFO overflow happens, should the new entry still be pushed, overwriting the oldest one. If 0 then new entry is lost.

Defaut value: CFG_OVERFLOW_INT | CFG_KEY_INT | CFG_USE_MODS

Interrupt status register (REG_INT = 0x03)

When an interrupt happens, the register can be read to check what caused the interrupt. It's 1 byte in size.

Bit Name Description
7 N/A Currently not implemented.
6 INT_TOUCH The interrupt was generated by a trackpad motion.
5 INT_GPIO The interrupt was generated by a input GPIO changing level.
4 INT_PANIC Currently not implemented.
3 INT_KEY The interrupt was generated by a key press.
2 INT_NUMLOCK The interrupt was generated by Num Lock.
1 INT_CAPSLOCK The interrupt was generated by Caps Lock.
0 INT_OVERFLOW The interrupt was generated by FIFO overflow.

After reading the register, it has to manually be reset to 0x00.

For INT_GPIO check the bits in REG_GIN to see which GPIO triggered the interrupt. The GPIO interrupt must first be enabled in REG_GIC.

Key status register (REG_KEY = 0x04)

This register contains information about the state of the fifo as well as modified keys. It is 1 byte in size.

Bit Name Description
7 N/A Currently not implemented.
6 KEY_NUMLOCK Is Num Lock on at the moment.
5 KEY_CAPSLOCK Is Caps Lock on at the moment.
0-4 KEY_COUNT Number of items in the FIFO waiting to be read.

Backlight control register (REG_BKL = 0x05)

Internally a PWM signal is generated to control the keyboard backlight, this register allows changing the brightness of the backlight. It is 1 byte in size, 0x00 being off and 0xFF being the brightest.

Default value: 0xFF.

Debounce configuration register (REG_DEB = 0x06)

Currently not implemented.

Default value: 10

Poll frequency configuration register (REG_FRQ = 0x07)

Currently not implemented.

Default value: 5

Chip reset register (REG_RST = 0x08)

Reading or writing to this register will cause a SW reset of the chip.

FIFO access register (REG_FIF = 0x09)

This register can be used to read the top of the key FIFO. It returns two bytes, a key state and a key code.

Possible key states:

Value State
1 Pressed
2 Pressed and Held
3 Released

Secondary backlight control register (REG_BK2 = 0x0A)

Internally a PWM signal is generated to control a secondary backlight (for example, a screen), this register allows changing the brightness of the backlight. It is 1 byte in size, 0x00 being off and 0xFF being the brightest.

Default value: 0xFF.

GPIO direction register (REG_DIR = 0x0B)

This register controls the direction of the GPIO expander pins, each bit corresponding to one pin. It is 1 byte in size.

The actual pin[7..0] to MCU pin assignment depends on the board, see <board>.h of the board for the assignments.

Any bit set to 1 means the GPIO is configured as input, any bit set to 0 means the GPIO is configured as output.

Default value: 0xFF (all GPIOs configured as input)

GPIO input pull enable register (REG_PUE = 0x0C)

If a GPIO is configured as an input (using REG_DIR), a optional pull-up/pull-down can be enabled.

This register controls the pull enable status, each bit corresponding to one pin. It is 1 byte in size.

The actual pin[7..0] to MCU pin assignment depends on the board, see <board>.h of the board for the assignments.

Any bit set to 1 means the input pull for that pin is enabled, any bit set to 0 means the input pull for that pin is disabled.

The direction of the pull is done in REG_PUD.

When a pin is configured as output, its bit in this register has no effect.

Default value: 0 (all pulls disabled)

GPIO input pull direction register (REG_PUD = 0x0D)

If a GPIO is configured as an input (using REG_DIR), a optional pull-up/pull-down can be configured.

The pull functionality is enabled using REG_PUE and the direction of the pull is configured using this register, each bit corresponding to one pin. This register is 1 byte in size.

The actual pin[7..0] to MCU pin assignment depends on the board, see <board>.h of the board for the assignments.

Any bit set to 1 means the input pull is set to pull-up, any bit set to 0 means the input pul is set to pull-down.

When a pin is configured as output, its bit in this register has no effect.

Default value: 0xFF (all pulls set to pull-up, if enabled in REG_PUE and set to input in REG_DIR)

GPIO value register (REG_GIO = 0x0E)

This register contains the values of the GPIO Expander pins, each bit corresponding to one pin. It is 1 byte in size.

The actual pin[7..0] to MCU pin assignment depends on the board, see <board>.h of the board for the assignments.

If a pin is configured as an output (via REG_DIR), writing to this register will change the value of that pin.

Reading from this register will return the values for both input and output pins.

Default value: Depends on pin values

GPIO interrupt config register (REG_GIC = 0x0F)

If a GPIO is configured as an input (using REG_DIR), an interrupt can be configured to trigger when the pin's value changes.

This register controls the interrupt, each bit corresponding to one pin.

The actual pin[7..0] to MCU pin assignment depends on the board, see <board>.h of the board for the assignments.

Any bit set to 1 means the input pin will trigger and interrupt when changing value, any bit set to 0 means no interrupt for that pin is triggered.

When an interrupt happens, the GPIO that triggered the interrupt can be determined by reading REG_GIN. Additionally, the INT_GPIO bit will be set in REG_INT.

Default value: 0x00

GPIO interrupt status register (REG_GIN = 0x10)

When an interrupt happens, the register can be read to check which GPIO caused the interrupt, each bit corresponding to one pin. This register is 1 byte in size.

The actual pin[7..0] to MCU pin assignment depends on the board, see <board>.h of the board for the assignments.

After reading the register, it has to manually be reset to 0x00.

Default value: 0x00

Key hold threshold configuration (REG_HLD = 0x11)

This register can be read and written to, it is 1 byte in size.

The value of this register (expressed in units of 10ms) is used to determine if a "press and hold" state should be entered.

If a key is held down longer than the value, it enters the "press and hold" state.

Default value: 30 (300ms)

Device I2C address (REG_ADR = 0x12)

The address that the device shows up on the I2C bus under. This register can be read and written to, it is 1 byte in size.

The change is applied as soon as a new value is written to the register. The next communication must be performed on the new address.

The address is not saved after a reset.

Default value: 0x1F

Interrupt duration (REG_IND = 0x13)

The value of this register determines how long the INT/IRQ pin is held LOW after an interrupt event happens.This register can be read and written to, it is 1 byte in size.

The value of this register is expressed in ms.

Default value: 1 (1ms)

The configuration register 2 (REG_CF2 = 0x14)

This register can be read and written to, it's 1 byte in size.

This register is a bit map of various settings that can be changed to customize the behaviour of the firmware.

See REG_CFG for additional settings.

Bit Name Description
7 N/A Currently not implemented.
6 N/A Currently not implemented.
5 N/A Currently not implemented.
4 N/A Currently not implemented.
3 N/A Currently not implemented.
2 CF2_USB_MOUSE_ON Should trackpad events be sent over USB HID.
1 CF2_USB_KEYB_ON Should key events be sent over USB HID.
0 CF2_TOUCH_INT Should trackpad events generate interrupts.

Default value: CF2_TOUCH_INT | CF2_USB_KEYB_ON | CF2_USB_MOUSE_ON

Trackpad X Position(REG_TOX = 0x15)

This is a read-only register, it is 1 byte in size.

Trackpad X-axis position delta since the last time this register was read.

The value reported is signed and can be in the range of (-128 to 127).

When the value of this register is read, it is afterwards reset back to 0.

It is recommended to read the value of this register often, or data loss might occur.

Default value: 0

Trackpad Y position (REG_TOY = 0x16)

This is a read-only register, it is 1 byte in size.

Trackpad Y-axis position delta since the last time this register was read.

The value reported is signed and can be in the range of (-128 to 127).

When the value of this register is read, it is afterwards reset back to 0.

It is recommended to read the value of this register often, or data loss might occur.

Default value: 0

Version history

v1.0:
- Initial release

See here for the legacy project's history: https://github.com/solderparty/bbq10kbd_i2c_sw#version-history

About

a fork with intended new features to the solderparty bbq20kbd

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • C 90.9%
  • Python 7.3%
  • CMake 1.8%