APA102_Pi is a pure python library to drive APA102 type LED strands. It is supposed to work on a Raspberry Pi, and is not tested on any other platform.
APA102 LEDs are typically 5050 type LEDs with an additional driver chip per LED. The driver chip takes care of receiving the desired colour via its input lines, and then holding this colour until a new command is received.
Depending on where these LEDs are bought, they might be called "APA102", "Superled", or "DotStar". They should not be confused with the three-wire WS2812 LEDs, also known as "NeoPixel".
The really nice part about the driver chip is this: Once it has received its own colour command, it forwards any further colour commands from its input to its output lines. This allows to easily chain multiple LEDs together. Colour command #1 lights the first LED, command #2 the next LED, etc. Sending e.g. 300 colour commands lights an entire 5 Meter, 60 LEDs per Meter strip.
The library is designed to take care of the details about sending colour commands. It is supposed to be educational, and is therefore written in Python. The library is fast enough to produce nice colour effects on a 300 LED strand, even though it is running via the Python interpreter. However, if you need something really fast, e.g. to drive a small "display" based on APA102 LEDs with 15 frames per second, then you have to look elsewhere.
- A Raspberry Pi, running an up-to-date version of Raspbian (the library is tested with the 2016-02-09 version of Raspbian Jessie Lite).
- SPI enabled and active (raspi-config, Advanced Options, SPI, Enable and load the module by default)
- The SPI must be free and unused
- A library named "spidev", Version 3. I used the one from here: https://github.com/doceme/py-spidev
- Python 3: Some people tried with Python 2 and reported it working, but I can't vouch for this myself. I used Python 3 for all development and test. Note that you need to install "spidev" with Python 3! If you install with Python 2, then the library is invisible for Python 3 applications.
Ideally, a 5$ Raspberry Pi Zero is dedicated to the task of driving the LEDs. The connector to the LED stripe can be soldered directly to the correct ports on the board.
The Raspberry Pi is a 3.3 Volt device, and the APA102 LEDs are 5 Volt devices. Therefore it's possible that the 3.3 Volt SPI signal is not being recognized by the LED driver chips. To avoid this risk, use a 74AHCT125 or 74AHC125 level shifter for both the clock and the MOSI signal.
Without a level shifter, the wiring is very simple:
- LED ground to one of the Raspberry ground pins
- LED Data to Raspberry SPI MOSI
- LED Clock to Raspberry SPI SCLK
The LED stripe uses a lot of power. If you try to power the LEDs from the Raspberry Pi, you will most likely immediately kill the Raspberry! Therefore I recommend not to connect the power line of the LED with the Raspberry. To be on the safe side, use a separate USB power supply for the Raspberry, and a strong 5V supply for the LEDs. If you use a level shifter, power it from the 5V power supply as well.
Having said this, you can power the Raspberry from the same power supply as the LED stripes (instead of using an extra USB power supply). If you decide to do this, make sure to never power the Raspberry Pi from its USB power supply, or you risk that the LEDs try to take power from the Raspberry.
All combined, this is my extremely low-tech wiring diagram:
And here it is, the finished contraption running a "rainbow" program:
Plugged into the USB port is a WLAN stick. This way I can reprogram the light show from my desk, even if the strips are installed outside as a christmas light. Compare this to an Arduino/WS2812 based installation: To reprogram one has to take the Arduino inside, or a laptop outside.
Videos can't be embedded yet, so head over to youtube: https://youtu.be/N0MK1z8W-1U
Because the Raspberry Pi Zero runs headless, the Raspbian Lite image was used. This image only contains the bare minimum of packages, therefore some packages have be installed manually. Of course, you can use the full raspbian jessie image and save yourself the installation steps.
Make sure that your Raspberry Pi is working and has a network connection. Also make sure that your installation is current (sudo apt-get update and sudo apt-get upgrade). This is what you then need to do in order to get the library up and runnig:
- Activate SPI: sudo raspi-config; Go to "Advanced Options"; Go to "SPI"; Choose "Yes", "Ok", "Yes" again, "Ok" again, and then exit the tool and reboot
- Install the git client: sudo apt-get install git
- Prepare GIT: git config --global user.name "John Doe" && git config --global user.email [email protected]
- Install Python 3: sudo apt-get install python3 && sudo apt-get install python3-dev
- Fetch the spidev library: cd /tmp && wget https://github.com/doceme/py-spidev/archive/master.zip && unzip master.zip
- Install the library: cd py-spidev-master && sudo python3 ./setup.py install
- Create a development directory and change into it: mkdir ~/Development && cd ~/Development
- Get the APA102 Library and sample light programs: git clone https://github.com/tinue/APA102_Pi.git
- You might want to set the number of LEDs to match your strip: cd APA102_Pi && nano runColorCycle.py; Update the number, Ctrl-X and "Yes" to save.
- Run the sample lightshow: python3 runColorCycle.py
- 2015-04-13: Initial version
- 2015-12-04: Add documentation
- 2015-12-11: Rewrote the examples, driver itself is unchanged
- 2015-12-17: Fixes for reported problems; Update all of the color samples; Decouple number of steps from number of LEDs
- 2016-03-25: Merged changes from kapacuk: Allow stripes with different color coding than RGB