Skip to content

lgeek/h107_rev

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

9 Commits
 
 
 
 

Repository files navigation

WARNING: information distributed in the hope that it will be useful, but without any warranty.

Copyright (C) Cosmin Gorgovan 2014. This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Hubsan X4 H107*

Hubsan H107 is a series of low cost ready-to-fly micro quadcopters. There are 4 models:

  • H107 - the base model, uses 7x20 mm coreless brushed motors and 240 mAh LiPo cells
  • H107L - adds an upwards pointing LED on each arm
  • H107C - adds a camera which can record to a micro-SD card and upgrades to 8x20mm coreless brushed motors and 380 mAh LiPo cells
  • H107D - is similar to H107C but it removes the micro-SD card and adds a video transmitter for First Person View (FPV) flying

Why reverse engineer it?

When I've started I was just looking for a micro-sized low cost hardware platform with widely available spare parts for which to write my own flight controller software. In the meantime, I've realised there are at least two possible applications which might be of interest to the general RC community:

  • repurposing the tiny (3 x 2 cm) low cost ($10-$15) controller board which contains a Nuvoton MINI54 (Cortex-M0 based) microcontroller, a 3 axis gyroscope, a 3 axis accelerometer, an A7105 wireless transceiver and 4 power MOSFETS capable of driving brushed motors

  • writing custom software to improve or extend functionality of the H107 (for example to make it work with other radio transmitters that use A7105 (e.g. flysky), to enable flying in acrobatic mode, to increase pitch and roll rates)

Scope of this project

  • I've mostly looked at the plain H107 model. H107L is very similar and I expect everything to apply to it as well. I have no plans regarding H107C and I haven't looked at H107D yet, but both seem reasonably similar to the base model. H107D is on my TODO list, there's some interest in using its FPV module on other platforms.

  • I've identified and found documentation for all ICs

  • I've traced all the connections and PCB traces required to develope a feature-equivalent firmware from scratch

  • I'm publishing high quality photos of the PCB which should be sufficient to verify and/or extend my analysis

Other sources of relevant documentation

  • Deviation TX firmware developers have reversed engineered the radio protocol here.

Hardware

Drone

Below is a picture of the H107 PCB top (left side of the picture is mounted at the front of the quad):

![H107 PCB top] (https://raw.githubusercontent.com/lgeek/h107_rev/master/img/h107/pcb_top_overview.jpg)

From left to right, we have:

  • the two blue LEDs which look like eyes, with the antenna between them
  • Amicom A7105 Transceiver covered by the crystal in cylindrical package - replaced with an SMD crystal in later revisions
  • below the A7105 and slightly to the right: Invensense MPU-3050 3 axis gyroscope
  • middle, top, the largest package: Nuvoton MINI54ZAN MCU - marked HUBSAN HBS001 in later revisions
  • below and slightly to the right of the MINI54 MCU: mCube MC3220 3 axis accelerometer - later replaced with MC3210 - it was a real PITA to identify
  • below and to the right of the M3220: Torex XC6206 3V LDO regulator
  • 4 identical devices aligned vertically and marked 122W: unknown N-Channel power MOSFETs
  • battery power input

There's nothing particularly interesting about the passives.

All ICs are orientated according to the silkscreen marking, the white circle shows pin 1.

For comparison, below are an overview of the H107L PCB and a macro showing the IC markings much more clearly.

H107L PCB top

H107L PCB macro

Datasheets

Debugging connections

The picture below shows the goodies on the bottom side of H107L: the D and C pins are SWDIO and SWCLK respectively! The pad marked R is reset. H107 includes the same pads in more or less the same position, although the rest of the bottom layout is slightly different.

H107L PCB bottom

Pinouts and connections

MINI54ZAN:

1 - voltage divider (10K from GND and 10K from VBAT) - used to detect battery voltage

2 - reset pad

3 - LED3-

4 - NC

5 - NC

6 - MC32x0 INT

7 - I2C SDA (MC32x0, MPU-3050)

8 - I2C SCL (MC32x0, MPU-3050)

9 - MPU-3050 INT

10 - NC

11 - H107: NC, H107L: A7105 CKO

12 - GND

13 - H107: unpopulated pad, H107L: LED5+

14 - MOSFET gate for motor front, left

15 - MOSFET gate for motor back, left

16 - MOSFET gate for motor back, right

17 - MOSFET gate for motor front, right

18 - H107: NC, H107L, LED6+

19 - SWDCLK

20 - SWDIO

21 - NC

22 - NC

23 - NC

24 - LED4-

25 - NC

26 - NC

27 - H107: VREG, H107L: NC

28 - VREG

29 - A7105 GIO1

30 - A7105 SDIO

31 - A7105 SCK

32 - A7105 SCS

The two LEDs on the PCB are connected in parallel with LED3 and LED4 respectively.

Transmitter

H107D TX PCB

H107D TX PCB top H107D TX PCB bottom

Software

The MCU is read and write protected, so the firmware image can't be directly read out. Glitching - it's clocked by IRC :( - or a software vulnerability might allow bypassing the protection, but I'm not sure it's worth the time.

The MCU can be unlocked (which also erases the firmware) using NU-LINK and Nuvoton's proprietary software. It would be useful to reverse engineer the unlocking procedure in order to drop the requirement for this programmer.

About

Reverse engineering Hubsan H107* micro quadcopters

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published