ErpNet.FP is a light-weight multi-platform Http server facilitating printing to fiscal printers through simple JSON Api. The library provides methods to detect, get status, print receipts, reports and other documents to fiscal printers.
The ErpNet.FP http server provides a REST API with JSON input/output, which prints documents transactionally and returns result status.
The http server receives input through the REST API and uses different transports to communicate with the fiscal printers. The transports include:
- COM serial connection
- Bluetooth connection through mapping to COM port
- TCP/IP
- etc.
Shortcut to Download
All communication with the ErpNet.FP print server is based on the Net.FP (Net Fiscal Protocol).
The print server accepts documents for printing, using JSON based protocol. For example, this would print the specified receipt to dt517985, which is the printerId of one of the detected printers, listed with GET /printers (see below for printerId explanation):
POST /printers/dt517985/receipt
{
"uniqueSaleNumber": "DT279013-0001-0000001",
"items": [
{
"text": "Cheese",
"quantity": 1,
"unitPrice": 12,
"taxGroup": 2
},
{
"type": "comment",
"text": "Additional comment to the cheese..."
},
{
"text": "Milk",
"quantity": 2,
"unitPrice": 10,
"taxGroup": 2,
"priceModifierValue": 10,
"priceModifierType": "discount-percent"
},
{
"type": "footer-comment",
"text": "YOU ARE WELCOME!"
}
],
"payments": [
{
"amount": 30,
"paymentType": "cash"
}
]
}For more information, see the full documentation of the protocol.
The most important result is the "ok" field. It contains "true" when the POST operation was successful, otherwise - "false". If there was error, "ok" would be "false".
If "ok"="false", it is guaranteed, that at least one message of type "error" would be present.
The error and warning messages have standardized codes across all manufacturers. The standard error and warning codes are listed in the Error and Warning Codes file.
The standard error codes are a subset of all manufacturer codes and flags. In some cases, the specific manufacturer codes, flags and messages could contain more detailed information. The manufacturer code, when available, is contained in the "originalCode" field. The problem with using the manufacturer codes is that they are different for each manufacturer. For some manufacturers they are not even present (there might be just some status flags). The manufacturer codes can even change between revisions of printers of the same manufacturer. The standardized error and warning codes are guaranteed to be the same across all manufacturers and printer versions. Messages with "type": "info", have no codes, because they cannot be standardized.
{
"ok": "true",
"messages": [
{
"type": "info",
"text": "Serial number and number of FM are set"
},
{
"type": "info",
"text": "FM is formatted"
}
],
"receiptNumber": "0000085",
"receiptDateTime": "2019-05-17T13:55:18",
"receiptAmount": 30,
"fiscalMemorySerialNumber": "02517985"
}{
"ok": "true",
"messages": [
{
"type": "warning",
"code": "W201",
"text": "The fiscal memory almost full"
},
{
"type": "info",
"text": "Serial number and number of FM are set"
},
{
"type": "info",
"text": "FM is formatted"
}
],
"deviceDateTime": "2019-05-10T15:50:00"
}{
"ok": "false",
"messages": [
{
"type": "error",
"code": "E201",
"text": "The fiscal memory is full"
},
{
"type": "info",
"text": "Serial number and number of FM are set"
},
{
"type": "info",
"text": "FM is formatted"
}
]
}Eager to try? You can list and download the binaries for ErpNet.FP.Server:
- Prerequisites for ErpNet.FP on Windows.
- There is no need for .Net installation.
- Everything that is needed is included in the MSI installer.
Download: Installer for Windows 32/64
The Windows installer setups or updates the ErpNet.FP Fiscal Print Server on a Windows 32 or 64 bit OS. The installer unpacks and installs a Windows service, called "ErpNet.FP". There is no UI, but when the service is running in the default configuration, you can browse the Admin page at http://localhost:8001.
- Prerequisites for ErpNet.FP on Windows.
- There is no need for .Net installation.
- Everything that is needed is included in the Zip files below.
Download 32 bit (x86): win-x86.zip - Windows 32 bit
Download 64 bit (x64): win-x64.zip - Windows 64 bit
Download and unzip the file in a folder. Inside the folder you will find executable file: ErpNet.FP.Server.exe. To start the printing service, run ErpNet.FP.Server.exe, or register the executable as a Windows service. When the service is running in the default configuration, you can browse the Admin page at http://localhost:8001.
Download 64 bit - osx-x64.zip - macOS - You can download and unzip the server in a folder.
Inside the unzipped folder, run it from console/terminal with:
./ErpNet.FP.ServerWhen the service is running in the default configuration, you can browse the Admin page at http://localhost:8001.
Download 64 bit - linux-x64.zip - Linux x64 - You can download and unzip the server.
Because of the serial ports default permissions, run it from sudoer, with sudo, or in the root user context. For convenience, create a systemd service config file, get more info how to do it here Systemd: Service File Examples. The other way is to run it from non-root user, but that user should have permissions to read and write to serial ports. When the service is running in the default configuration, you can browse the Admin page at http://localhost:8001.
Download 64 bit - linux-arm.zip - Linux Arm - You can download and unzip the server.
This version is compatible with Raspberry PI OS, Raspbian, and 64 bit Arm devices like Raspberry PI 3B+, Raspberry PI 2 and up. Because of the serial ports default permissions, run it from sudoer, with sudo, or in the root user context. For convenience, create a systemd service config file, get more info how to do it here Systemd - Raspberry Pi Documentation. The other way is to run it from non-root user, but that user should have permissions to read and write to serial ports. When the service is running in the default configuration, you can browse the Admin page at http://localhost:8001.
Important: The requirement for running ARM CPUs is to support at least the vfpv4d32 floating point feature. This is why we prefer to support only 64 bit CPUs, because they support that feature and more... For reference see: Issue 17043 at dotnet/coreclr.
For debugging purposes, there is a link to debug.log and it's folder in the Admin page. It contains debug information for every event that occured while using the service.
The server configuration options are located in a file, called "appsettings.json". For more information, see Configuration. It is recommended that you use the Admin page, or through /service API to edit the settings in this file rather than edit it directly.
Most fiscal printers or cash register should be in "Fiscal Printer" mode in order to accept commands from the PC through the serial interface. Refer to your printer manual how to setup the fiscal printer mode.
The following non-comprehensive article contains the setup procedure for some fiscal printers:
Each printer is identified by its printerId. Although the library consumer does not need to know the exact specifics of the algorithm for generating the printerId, they are provided here for completeness:
-
For locally connected printers, the printerId is the printer serial number. For example: "dy448967"
-
If a local printer is connected through multiple transports (for example: both COM and BT), the id for each next transport connection is assigned a consecutive number. For example: "dy448967_1" Note: The algorithm runs always in the same order. Unless transports are changed, the id would remain constant. However, it is advised to always use the default, non-numeric id.
-
For network printers, the printerId is provided in the configuration file. For example: "FP_Room1"
When a printer is detected, the http server saves something, called printer Uri. The Uri contains the connection information to connect to the printer. It contains details about printer driver, transport and path to the printer. It is similar to the connection string pattern. Example Uris:
- bg.dy.isl.com://COM5
- bg.dy.isl.com://COM3
- bg.dt.x.isl.com://COM21
- bg.zk.zfp.http://fp5.mycompany.com
- bg.dt.p.isl.tcp://192.168.1.77:9100
- etc.
The printer Uri is currently used only internally in the http server. Still, it is exposed as part of the device info. In the future, there might be methods to use the printers through their Uri.
Currently, the http server is available for:
- Windows 32/64 bit
- macOS 10.10 and up
- Linux x64
- Linux Arm
The library supports printers from the following manufacturers:
- Datecs (http://www.datecs.bg)
- Tremol (https://www.tremol.bg)
- Daisy (https://daisy.bg)
- Eltrade (https://www.eltrade.com)
- Incotex (http://www.incotex.bg)
- ISL (http://isl.bg)
If you want your device to be supported, please contact us, and we will try our best to help you!
- Datecs DP-25, firmware: 263453 08Nov18 131, protocol: bg.dt.c.isl.com
- Datecs WP-50, firmware: 261403 08Nov18 1050, protocol: bg.dt.c.isl.com
- Datecs FP-2000, firmware: 1.00BG 23NOV18 1000, protocols: bg.dt.p.isl.com, bg.dt.p.isl.tcp
- Datecs FP-700X, firmware: 266207 29Jan19 1634, protocols: bg.dt.x.isl.com, bg.dt.x.isl.tcp
- Daisy CompactM, firmware: ONL-4.01BG, protocol: bg.dy.isl.com
- Daisy CompactM, firmware: ONL01-4.01BG, protocol: bg.dy.isl.com
- Eltrade A1, firmware: KL5101.1811.0.3 15Nov18 15:49, protocol: bg.ed.isl.com
- Tremol FP01-KL-V2, firmware: 99C4, protocol: bg.zk.v2.zfp.com
- Tremol M20, firmware: Ver. 1.01 TRA20 C.S. 25411, protocol: bg.zk.zfp.com
- Incotex 300SM KL-Q, firmware: 2.11 Jan 22 2019 14:00, protocol: bg.in.isl.com
- ISL5011S-KL, firmware: BG R1 21.01.201948, protocol: bg.is.icp.com
-
bg.dt.c.isl - Datecs WP-50, Datecs DP-05, Datecs DP-05B, Datecs DP-05C, Datecs DP-25, Datecs DP-35, Datecs DP-150, Datecs DP-15
-
bg.dt.p.isl - Datecs FP-650, Datecs FP-800, Datecs FP-2000, Datecs FMP-10, Datecs SK1-21F, Datecs SK1-31F
-
bg.dt.x.isl - Datecs DP-25X, Datecs FMP-350X, Datecs FP-700X, Datecs WP-500X, Datecs FMP-55X, Datecs WP-50X, Datecs FP-700X, Datecs DP-150X, Datecs WP-25X, Datecs FP-700XE
-
bg.zk.zfp - Tremol A19Plus, Tremol S21, Tremol M23, Tremol M20, Tremol FP15, Tremol SB, Tremol S25, Tremol FP24
-
bg.zk.v2.zfp - Tremol Z-KL-V2, Tremol ZM-KL-V2, Tremol ZS-KL-V2, Tremol FP01-KL V2, Tremol FP05-KL V2, Tremol M-KL-V2, Tremol S-KL-V2, Tremol FP15 KL V2, Tremol FP03-KL V2, Tremol FP07-KL V2, Tremol FP01, Tremol FP21
-
bg.ed.isl - Eltrade A1 KL, Eltrade A1 KL, Eltrade A3 KL, Eltrade B1 KL, Eltrade PRP 250F KL, Eltrade A6 KL, Eltrade B3 KL, EPSON TM - T810F KL модел 01, EPSON TM - T81F KL модел 03, ELTRADE PRP 250F KL
-
bg.dy.isl - Daisy Compact S, Daisy Compact M, Daisy eXpert SX 01, Daisy eXpert SX, Daisy Compact M 02, Daisy Compact S 01, Daisy Perfect M 01, Daisy MICRO C 01, Daisy Compact M 01, Daisy eXpert 01, Daisy Perfect S 01, Daisy FX 1300, Daisy FX 1200C, Daisy Perfect SA, Daisy FX 21 01
-
bg.in.isl - Incotex 133 KL-Q, Incotex 181 KL-Q, Incotex 777, Incotex 300SM KL-Q, Incotex 300S KL-Q
-
bg.is.icp - ISL5011S-KL
-
Didn't find your device on the list? Please, create an issue here in the project and we will check whether we can support it with the current set of protocols or we need to implement a new one.
This is a list of default credentials we use in the library, when there is no exclusive override of the values in the Json fields "operator" and "operatorPassword", while you make a Json requests to the fiscal device.
- bg.dt.c.isl - "operator" : "1", "operatorPassword": "1"
- bg.dt.p.isl - "operator" : "1", "operatorPassword": "0000"
- bg.dt.x.isl - "operator" : "1", "operatorPassword": "0000"
- bg.zk.zfp - "operator" : "1", "operatorPassword": "0000"
- bg.zk.v2.zfp - "operator" : "1", "operatorPassword": "0000"
- bg.ed.isl - "operator" : "1", "operatorPassword": N/A
- bg.dy.isl - For receipts: "operator" : "1", "operatorPassword": "1", and for reversalReceipts: "operator" : "20", "operatorPassword": "9999"
- bg.in.isl - "operator" : "1", "operatorPassword": "1"
- bg.is.icp - "operator" : "1", "operatorPassword": N/A
To compile and run the source code, you will need .Net Core 3.0 SDK installed.
To build the binaries into Published folder and .zip files into Output folder, just write this line in the console, while you are in the ErpNet.FP folder:
dotnet msbuild output.xmlIf you are under Windows, you can install Wix toolset - Wix 3.11 and you will be able to build ErpNet.FP.Setup and to get the Windows MSI setup file into the Output folder.
As IDE for Windows, you can use Visual Studio 2019. For macOS, you can use Visual Studio for Mac 8.3. For Linux, or as alternative for Windows and macOs, you can use Visual Studio Code.
ErpNet.FP is free, open and works great. Most people use ErpNet.FP without any kind of support.
Free support for ErpNet.FP is available on the https://www.facebook.com/groups/BgBusinessDev/. This group is monitored by a community of experts, including the core ErpNet.FP development team, who are able to resolve your problems with ErpNet.FP that you are likely to have. The main language of this group is Bulgarian, but you can post your questions in English.
"BSD Zero Clause License", see LICENSE.txt
See our Contributing document and our Code of Conduct document, to learn how to help us.