Custom Auto-generated Configs

[no ci]

generated/controllers/generated/engine_configuration_generated_structures_paralela.h

@@ -672,9 +672,10 @@ struct engine_configuration_s {
 	 */
 	Gpio canRxPin;
 	/**
+	 * Pin that activates the reduction/cut for shifting. Sometimes shared with the Launch Control pin
 	 * offset 36
 	 */
-	uint16_t unusedEtbExpAverageLength;
+	switch_input_pin_e torqueReductionTriggerPin;
 	/**
 	 * units: %
 	 * offset 38
@@ -963,9 +964,11 @@ struct engine_configuration_s {
 	 */
 	uint8_t mapSyncThreshold;
 	/**
+	 * How many % of ignition events will be cut
+	 * units: %
 	 * offset 443
 	 */
-	uint8_t unusedByteHere;
+	int8_t torqueReductionIgnitionCut;
 	/**
 	 * @@CYLINDER_BORE_TOOLTIP@@
 	 * units: mm
@@ -1774,9 +1777,11 @@ struct engine_configuration_s {
 	 */
 	brain_input_pin_e flexSensorPin;
 	/**
+	 * Since torque reduction pin is usually shared with launch control, most people have an RPM where behavior under that is Launch Control, over that is Flat Shift/Torque Reduction
+	 * units: rpm
 	 * offset 818
 	 */
-	uint16_t unused720;
+	uint16_t torqueReductionArmingRpm;
 	/**
 	 * offset 820
 	 */
@@ -2609,9 +2614,10 @@ struct engine_configuration_s {
 	 */
 	int idleStepperTotalSteps;
 	/**
+	 * Pedal position to realize that we need to reduce torque when the trigger pin is uuuh triggered
 	 * offset 1356
 	 */
-	int unusedInt3423423;
+	int torqueReductionArmingApp;
 	/**
 	 * Duration in ms or duty cycle depending on selected mode
 	 * offset 1360
@@ -2769,9 +2775,11 @@ struct engine_configuration_s {
 	 */
 	int16_t idlePidRpmDeadZone;
 	/**
+	 * For how long after the pin has been triggered will the cut/reduction stay active. After that, even if the pin is still triggered, torque is re-introduced
+	 * units: ms
 	 * offset 1488
 	 */
-	float unusedTargetVBatt;
+	float torqueReductionTime;
 	/**
 	 * See Over/Undervoltage Shutdown/Retry bit in documentation
 	offset 1492 bit 0 */
@@ -2958,9 +2966,11 @@ struct engine_configuration_s {
 	 */
 	float tpsDecelEnleanmentMultiplier;
 	/**
+	 * How many degrees of timing advance will be reduced during the Torque Reduction Time
+	 * units: deg
 	 * offset 1532
 	 */
-	uint32_t unusedAuxSerialSpee;
+	float torqueReductionIgnitionRetard;
 	/**
 	 * units: voltage
 	 * offset 1536

generated/controllers/generated/rusefi_generated_paralela.h

@@ -1294,7 +1294,7 @@
 #define show_Proteus_presets false
 #define show_test_presets false
 #define show_vvt_output_pin true
-#define SIGNATURE_HASH 3377314616
+#define SIGNATURE_HASH 2758805459
 #define SIMULATOR_TUNE_BIN_FILE_NAME "generated/simulator_tune_image.bin"
 #define SIMULATOR_TUNE_BIN_FILE_NAME_PREFIX "generated/simulator_tune_image"
 #define SIMULATOR_TUNE_BIN_FILE_NAME_SUFFIX ".bin"
@@ -1753,7 +1753,7 @@
 #define ts_show_wastegate_sensor true
 #define ts_show_wbo_canbus_index true
 #define ts_show_wbo_canbus_set_index true
-#define TS_SIGNATURE "rusEFI master.2024.09.25.paralela.3377314616"
+#define TS_SIGNATURE "rusEFI master.2024.09.26.paralela.2758805459"
 #define TS_SIMULATE_CAN '>'
 #define TS_SIMULATE_CAN_char >
 #define TS_SINGLE_WRITE_COMMAND 'W'

generated/controllers/generated/signature_paralela.h

@@ -2,5 +2,5 @@
 // was generated automatically by rusEFI tool config_definition-all.jar based on gen_config.sh by SignatureConsumer
 //
 
-#define SIGNATURE_HASH 3377314616
-#define TS_SIGNATURE "rusEFI master.2024.09.25.paralela.3377314616"
+#define SIGNATURE_HASH 2758805459
+#define TS_SIGNATURE "rusEFI master.2024.09.26.paralela.2758805459"

generated/tunerstudio/generated/rusefi_paralela.ini

@@ -38,12 +38,12 @@ enable2ndByteCanID = false
 
 [MegaTune]
  ; https://rusefi.com/forum/viewtopic.php?p=36201#p36201
-	signature	= "rusEFI master.2024.09.25.paralela.3377314616"
+	signature	= "rusEFI master.2024.09.26.paralela.2758805459"
 
 [TunerStudio]
 	queryCommand	= "S"
 	versionInfo	= "V"  ; firmware version for title bar.
-	signature= "rusEFI master.2024.09.25.paralela.3377314616" ; signature is expected to be 7 or more characters.
+	signature= "rusEFI master.2024.09.26.paralela.2758805459" ; signature is expected to be 7 or more characters.
 
 	; TS will try to use legacy temp units in some cases, showing "deg F" on a CLT gauge that's actually deg C
 	useLegacyFTempUnits = false
@@ -123,7 +123,7 @@ mainRelayPin = bits, U16, 28, [0:8], $output_pin_e_list
 sdCardCsPin = bits, U16, 30, [0:8], $gpio_list
 canTxPin = bits, U16, 32, [0:8], $gpio_list
 canRxPin = bits, U16, 34, [0:8], $gpio_list
-unusedEtbExpAverageLength = scalar, U16, 36, "", 1, 0, 0, 32000, 0
+torqueReductionTriggerPin = bits, U16, 36, [0:8], $switch_input_pin_e_list
 launchFuelAdderPercent = scalar, S08, 38, "%", 1, 0, 0, 100, 0
 etbJamTimeout = scalar, U08, 39, "sec", 0.02, 0, 0, 5, 2
 tachOutputPin = bits, U16, 40, [0:8], $output_pin_e_list
@@ -213,7 +213,7 @@ cylindersCount = scalar, U32, 436, "", 1, 0, 1, 12, 0
 firingOrder = bits, U08, 440, [0:6], "One Cylinder", "1-3-4-2", "1-2-4-3", "1-3-2-4", "1-5-3-6-2-4", "1-8-4-3-6-5-7-2", "1-2-4-5-3", "1-4-2-5-3-6", "1-2", "1-2-3-4-5-6", "1-2-3", "1-8-7-2-6-5-4-3", "1-5-4-2-6-3-7-8 Mustang", "1-6-3-2-5-4", "1-10-9-4-3-6-5-8-7_2", "1-7-5-11-3-9-6-12-2-8-4-10", "1-7-4-10-2-8-6-12-3-9-5-11", "1-4-3-2", "1-12-5-8-3-10-6-7-2-11-4-9", "1-2-7-8-4-5-6-3", "1-3-7-2-6-5-4-8 HO", "1-2-3-4-5-6-7-8-9", "INVALID", "1-2-3-4-5-6-7-8-9-10-11-12", "1-3-2", "1-2-3-4-5-6-7-8", "1-5-4-8-6-3-7-2", "1-4-3-6-2-5", "1-8-7-3-6-5-4-2", "1-6-2-4-3-5", "1-6-5-4-3-2", "1-4-5-2-3-6", "1-5-4-8-3-7-2-6 Voodoo", "1-6-5-10-2-7-3-8-4-9", "1-8-6-2-7-3-4-5 F136", "fo35", "fo36", "fo37", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID"
 justATempTest = scalar, U08, 441, "", 1, 0, 0, 100, 0
 mapSyncThreshold = scalar, U08, 442, "kPa", 1, 0, 0, 50, 0
-unusedByteHere = scalar, U08, 443, "", 1, 0, 0, 100, 0
+torqueReductionIgnitionCut = scalar, S08, 443, "%", 1, 0, 0, 100, 0
 cylinderBore = scalar, F32, 444, "mm", 1, 0, 0, 2000, 2
 fuelAlgorithm = bits, U08, 448, [0:2], "Speed Density", "MAF Air Charge", "Alpha-N", "Lua", "INVALID", "INVALID", "INVALID", "INVALID"
 ALSMaxTPS = scalar, U08, 449, "%", 1, 0, 0, 10, 0
@@ -430,7 +430,7 @@ max31855_cs6 = bits, U16, 810, [0:8], $gpio_list
 max31855_cs7 = bits, U16, 812, [0:8], $gpio_list
 max31855_cs8 = bits, U16, 814, [0:8], $gpio_list
 flexSensorPin = bits, U16, 816, [0:8], $brain_input_pin_e_list
-unused720 = scalar, U16, 818, "", 1, 0, 0, 32000, 0
+torqueReductionArmingRpm = scalar, U16, 818, "rpm", 1, 0, 0, 20000, 0
 stepperDirectionPinMode = bits, U08, 820, [0:1], "default", "default inverted", "open collector", "open collector inverted"
 mc33972spiDevice = bits, U08, 821, [0:2], "Off", "SPI1", "SPI2", "SPI3", "SPI4", "SPI5", "SPI6", "INVALID"
 stoichRatioSecondary = scalar, U08, 822, ":1", 0.1, 0, 5, 25, 1
@@ -692,7 +692,7 @@ knockDetectionWindowStart = scalar, F32, 1340, "angle", 1, 0, -1000, 1000, 2
 knockDetectionWindowEnd = scalar, F32, 1344, "angle", 1, 0, -1000, 1000, 2
 idleStepperReactionTime = scalar, F32, 1348, "ms", 1, 0, 1, 300, 0
 idleStepperTotalSteps = scalar, S32, 1352, "count", 1, 0, 5, 3000, 0
-unusedInt3423423 = scalar, S32, 1356, "", 1, 0, 0, 100, 0
+torqueReductionArmingApp = scalar, S32, 1356, "", 1, 0, 0, 20000, 0
 tachPulseDuractionMs = scalar, F32, 1360, "", 1, 0, 0, 100, 2
 wwaeTau = scalar, F32, 1364, "Seconds", 1, 0, 0, 3, 2
 alternatorControl_pFactor = scalar, F32, 1368, "", 1, 0, -10000, 10000, 4
@@ -741,7 +741,7 @@ throttlePedalUpVoltage = scalar, F32, 1476, "voltage", 1, 0, -6, 6, 2
 throttlePedalWOTVoltage = scalar, F32, 1480, "voltage", 1, 0, -6, 6, 2
 startUpFuelPumpDuration = scalar, S16, 1484, "seconds", 1, 0, 0, 6000, 0
 idlePidRpmDeadZone = scalar, S16, 1486, "RPM", 1, 0, 0, 800, 0
-unusedTargetVBatt = scalar, F32, 1488, "", 1, 0, 0, 100, 0
+torqueReductionTime = scalar, F32, 1488, "ms", 1, 0, 1, 300, 0
 mc33810DisableRecoveryMode = bits, U32, 1492, [0:0], "false", "true"
 mc33810Gpgd0Mode = bits, U32, 1492, [1:1], "false", "true"
 mc33810Gpgd1Mode = bits, U32, 1492, [2:2], "false", "true"
@@ -790,7 +790,7 @@ fan1ExtraIdle = scalar, U08, 1519, "%", 1, 0, 0, 100, 0
 uartConsoleSerialSpeed = scalar, U32, 1520, "BPs", 1, 0, 0, 1000000, 0
 tpsDecelEnleanmentThreshold = scalar, F32, 1524, "roc", 1, 0, 0, 200, 1
 tpsDecelEnleanmentMultiplier = scalar, F32, 1528, "coeff", 1, 0, 0, 200, 2
-unusedAuxSerialSpee = scalar, U32, 1532, "", 1, 0, 0, 100, 0
+torqueReductionIgnitionRetard = scalar, F32, 1532, "deg", 1, 0, -180, 180, 2
 throttlePedalSecondaryUpVoltage = scalar, F32, 1536, "voltage", 1, 0, -6, 6, 2
 throttlePedalSecondaryWOTVoltage = scalar, F32, 1540, "voltage", 1, 0, -6, 6, 2
 canBaudRate = bits, U08, 1544, [0:2], "50kbps", "83.33kbps", "100kbps", "125kbps", "250kbps", "500kbps", "1Mbps", "INVALID"
@@ -1730,6 +1730,7 @@ minimumOilPressureValues = array, U08, 25060, [8], "kPa", 10.0, 0, 0, 1000, 0
 	wastegatePositionMax = "Voltage when the wastegate is fully open.\nYou probably don't have one of these!\n1 volt = 1000 units"
 	idlePositionMin = "Voltage when the idle valve is closed.\nYou probably don't have one of these!"
 	idlePositionMax = "Voltage when the idle valve is open.\nYou probably don't have one of these!\n1 volt = 1000 units"
+	torqueReductionTriggerPin = "Pin that activates the reduction/cut for shifting. Sometimes shared with the Launch Control pin"
 	etbJamTimeout = "Time required to detect a stuck throttle."
 	acIdleExtraOffset = "Additional idle % while A/C is active"
 	manIdlePosition = "Value between 0 and 100 used in Manual mode"
@@ -1778,6 +1779,7 @@ minimumOilPressureValues = array, U08, 25060, [8], "kPa", 10.0, 0, 0, 1000, 0
 	displacement = "Engine displacement in litres"
 	cylindersCount = "Number of cylinder the engine has."
 	mapSyncThreshold = "Delta kPa for MAP sync"
+	torqueReductionIgnitionCut = "How many % of ignition events will be cut"
 	cylinderBore = "Cylinder diameter in mm"
 	fuelAlgorithm = "This setting controls which fuel quantity control algorithm is used.\nAlpha-N means drive by TPS commonly only used for NA engines\nSpeed Density requires MAP sensor and is the default choice for may installs\nMAF air charge is a cylinder filling based method that uses a mass air flow sensor."
 	crankingInjectionMode = "This is the injection strategy during engine start. See Fuel/Injection settings for more detail. It is suggested to use "Simultaneous"."
@@ -1902,6 +1904,7 @@ minimumOilPressureValues = array, U08, 25060, [8], "kPa", 10.0, 0, 0, 1000, 0
 	max31855_cs7 = "max31855_cs 7"
 	max31855_cs8 = "max31855_cs 8"
 	flexSensorPin = "Continental/GM flex fuel sensor, 50-150hz type"
+	torqueReductionArmingRpm = "Since torque reduction pin is usually shared with launch control, most people have an RPM where behavior under that is Launch Control, over that is Flat Shift/Torque Reduction"
 	stoichRatioSecondary = "Stoichiometric ratio for your secondary fuel. This value is used when the Flex Fuel sensor indicates E100, typically 9.0"
 	etbMaximumPosition = "Maximum allowed ETB position. Some throttles go past fully open, so this allows you to limit it to fully open."
 	sdCardLogFrequency = "Rate the ECU will log to the SD card, in hz (log lines per second)."
@@ -2036,6 +2039,7 @@ minimumOilPressureValues = array, U08, 25060, [8], "kPa", 10.0, 0, 0, 1000, 0
 	camInputsDebug4 = "camInputsDebug 4"
 	acIdleRpmTarget = "Idle target speed when A/C is enabled. Some cars need the extra speed to keep the AC efficient while idling."
 	warningPeriod = "set warningPeriod X"
+	torqueReductionArmingApp = "Pedal position to realize that we need to reduce torque when the trigger pin is uuuh triggered"
 	tachPulseDuractionMs = "Duration in ms or duty cycle depending on selected mode"
 	wwaeTau = "Length of time the deposited wall fuel takes to dissipate after the start of acceleration."
 	alternatorControl_offset = "Linear addition to PID logic"
@@ -2067,6 +2071,7 @@ minimumOilPressureValues = array, U08, 25060, [8], "kPa", 10.0, 0, 0, 1000, 0
 	throttlePedalWOTVoltage = "Pedal in the floor"
 	startUpFuelPumpDuration = "on IGN voltage detection turn fuel pump on to build fuel pressure"
 	idlePidRpmDeadZone = "If the RPM closer to target than this value, disable closed loop idle correction to prevent oscillation"
+	torqueReductionTime = "For how long after the pin has been triggered will the cut/reduction stay active. After that, even if the pin is still triggered, torque is re-introduced"
 	mc33810DisableRecoveryMode = "See Over/Undervoltage Shutdown/Retry bit in documentation"
 	enableExtendedCanBroadcast = "Send out board statistics"
 	useAuxSpeedForSlipRatio = "Use Aux Speed 1 as one of speeds for wheel slip ratio?"
@@ -2085,6 +2090,7 @@ minimumOilPressureValues = array, U08, 25060, [8], "kPa", 10.0, 0, 0, 1000, 0
 	uartConsoleSerialSpeed = "Band rate for primary TTL"
 	tpsDecelEnleanmentThreshold = "For decel we simply multiply delta of TPS and tFor decel we do not use table?!"
 	tpsDecelEnleanmentMultiplier = "Magic multiplier, we multiply delta of TPS and get fuel squirt duration"
+	torqueReductionIgnitionRetard = "How many degrees of timing advance will be reduced during the Torque Reduction Time"
 	throttlePedalSecondaryWOTVoltage = "Pedal in the floor"
 	veOverrideMode = "Override the Y axis (load) value used for the VE table.\nAdvanced users only: If you aren't sure you need this, you probably don't need this."
 	afrOverrideMode = "Override the Y axis (load) value used for the AFR table.\nAdvanced users only: If you aren't sure you need this, you probably don't need this."
@@ -6114,6 +6120,7 @@ menuDialog = main
 
 	menu = "&Advanced"
 		subMenu = smLaunchControl,			"Launch Control"
+		subMenu = FlatShiftSettingsDialog,	"Shift Torque Reduction (Flat Shift)"
 		subMenu = ignitionCylExtra,			"Cylinder offsets", 0
 
 		subMenu = std_separator
@@ -9558,6 +9565,16 @@ dialog = tcuControls, "Transmission Settings"
 		field = "Final Ignition Cut % Before launch",   finalIgnitionCutPercentBeforeLaunch,    {launchSparkCutEnable == 1}
 		field = "Fuel Cut",								launchFuelCutEnable,  {launchControlEnabled == 1}
 
+	dialog = TorqueReductionSettings, "Torque Reduction"
+		field = "Trigger Pin",		torqueReductionTriggerPin
+		field = "Time",				torqueReductionTime,			{torqueReductionTriggerPin != 0}
+		field = "Arming RPM",		torqueReductionArmingRpm,		{torqueReductionTriggerPin != 0}
+		field = "Arming APP",		torqueReductionArmingApp,		{torqueReductionTriggerPin != 0}
+		field = "Ignition Retard",	torqueReductionIgnitionRetard,	{torqueReductionTriggerPin != 0}
+		field = "Ignition Cut",		torqueReductionIgnitionCut,		{torqueReductionTriggerPin != 0}
+
+	dialog = FlatShiftSettingsDialog, "", border
+		panel = TorqueReductionSettings, West
 
 	dialog = smLaunchControl, "", border
 		panel = smLaunchControlWest, West

generated/tunerstudio/generated/signature_paralela.txt

@@ -1,4 +1,4 @@
 ! Generated by gen_signature.sh
 ! SIGNATURE_HASH is a built-in variable generated by config_definition-all.jar
 ! gen_signature.sh Using env variable branch [master]
-#define TS_SIGNATURE "rusEFI master.2024.09.25.paralela.@@SIGNATURE_HASH@@"
+#define TS_SIGNATURE "rusEFI master.2024.09.26.paralela.@@SIGNATURE_HASH@@"