Custom Auto-generated Configs

[no ci]

generated/console/binary/generated/output_channels.ini

@@ -28,7 +28,7 @@ dfcoActive = bits, U32, 0, [26:26]
 sd_active_wr = bits, U32, 0, [27:27]
 sd_active_rd = bits, U32, 0, [28:28]
 RPMValue = scalar, U16, 4, "RPM", 1, 0
-rpmAcceleration = scalar, S16, 6, "RPM acceleration", 1, 0
+rpmAcceleration = scalar, S16, 6, "RPM acceleration/Rate of Change/ROC", 1, 0
 speedToRpmRatio = scalar, U16, 8, "value", 0.01, 0
 unusedVehicleSpeedKph = scalar, U08, 10, "kph", 1, 0
 internalMcuTemperature = scalar, S08, 11, "deg C", 1, 0

generated/controllers/generated/engine_configuration_generated_structures_XYZ.h

@@ -2013,7 +2013,7 @@ struct engine_configuration_s {
 	bool enableCanVss : 1 {};
 	/**
 	offset 920 bit 8 */
-	bool enableInnovateLC2 : 1 {};
+	bool unusedSnableInnovateLC2 : 1 {};
 	/**
 	offset 920 bit 9 */
 	bool showHumanReadableWarning : 1 {};
@@ -2885,15 +2885,13 @@ struct engine_configuration_s {
 	 */
 	int16_t iacByTpsTaper;
 	/**
-	 * Auxiliary sensor serial, not to be confused with secondary calibration serial
 	 * offset 1500
 	 */
-	Gpio auxSerialTxPin;
+	Gpio unusedAuxSeria;
 	/**
-	 * Auxiliary sensor serial, not to be confused with secondary calibration serial
 	 * offset 1502
 	 */
-	Gpio auxSerialRxPin;
+	Gpio unusedAuxSerialRx;
 	/**
 	 * offset 1504
 	 */
@@ -2959,10 +2957,9 @@ struct engine_configuration_s {
 	 */
 	float tpsDecelEnleanmentMultiplier;
 	/**
-	 * units: BPs
 	 * offset 1532
 	 */
-	uint32_t auxSerialSpeed;
+	uint32_t unusedAuxSerialSpee;
 	/**
 	 * units: voltage
 	 * offset 1536

generated/controllers/generated/rusefi_generated_XYZ.h

@@ -1236,34 +1236,22 @@
 #define pin_output_mode_e_OM_OPENDRAIN 2
 #define pin_output_mode_e_OM_OPENDRAIN_INVERTED 3
 #define PRIME_CURVE_COUNT 8
-#define PROTOCOL_ACR_NAME "acr"
 #define PROTOCOL_ANALOG_CHART "analog_chart"
-#define PROTOCOL_COIL1_SHORT_NAME "c1"
+#define PROTOCOL_COIL_SHORT_PREFIX "c"
 #define PROTOCOL_CRANK1 "t1"
 #define PROTOCOL_CRANK2 "t2"
 #define PROTOCOL_ENGINE_SNIFFER "wave_chart"
 #define PROTOCOL_ES_DOWN "d"
 #define PROTOCOL_ES_UP "u"
 #define PROTOCOL_HELLO_PREFIX "***"
-#define PROTOCOL_HIP_NAME "HIP"
-#define PROTOCOL_HPFP_NAME "hpfp"
-#define PROTOCOL_INJ1_SHORT_NAME "i1"
-#define PROTOCOL_INJ1_STAGE2_SHORT_NAME "j1"
+#define PROTOCOL_INJ_SHORT_PREFIX "i"
+#define PROTOCOL_INJ_STAGE2_SHORT_PREFIX "j"
 #define PROTOCOL_KNOCK_SPECTROGRAMM "knock_spectrogram"
 #define PROTOCOL_MSG "msg"
 #define PROTOCOL_OUTPIN "outpin"
 #define PROTOCOL_SIGNATURE_PREFIX "rusEFI "
-#define PROTOCOL_TACH_NAME "tach"
 #define PROTOCOL_TEST_RESPONSE_TAG "ts_p_alive"
 #define PROTOCOL_VERSION_TAG "rusEfiVersion"
-#define PROTOCOL_VVT1_NAME "VVT1"
-#define PROTOCOL_VVT2_NAME "VVT2"
-#define PROTOCOL_VVT3_NAME "VVT3"
-#define PROTOCOL_VVT4_NAME "VVT4"
-#define PROTOCOL_WA_CHANNEL_1 "input1"
-#define PROTOCOL_WA_CHANNEL_2 "input2"
-#define PROTOCOL_WA_CHANNEL_3 "input3"
-#define PROTOCOL_WA_CHANNEL_4 "input4"
 #define RANGE_INPUT_COUNT 6
 #define REBOOT_COMMAND 0xbb
 #define SCRIPT_CURVE_16 16
@@ -1304,7 +1292,7 @@
 #define show_Proteus_presets false
 #define show_test_presets false
 #define show_vvt_output_pin true
-#define SIGNATURE_HASH 1349726135
+#define SIGNATURE_HASH 1057972626
 #define SIMULATOR_TUNE_BIN_FILE_NAME "generated/simulator_tune_image.bin"
 #define SIMULATOR_TUNE_BIN_FILE_NAME_PREFIX "generated/simulator_tune_image"
 #define SIMULATOR_TUNE_BIN_FILE_NAME_SUFFIX ".bin"
@@ -1742,7 +1730,6 @@
 #define ts_show_trigger_comparator false
 #define ts_show_trigger_overrides true
 #define ts_show_tunerstudio_port true
-#define ts_show_uegoSerial true
 #define ts_show_vbatt true
 #define ts_show_vehicle_speed_sensor true
 #define ts_show_vehicle_weight false
@@ -1754,7 +1741,7 @@
 #define ts_show_wastegate_sensor true
 #define ts_show_wbo_canbus_index true
 #define ts_show_wbo_canbus_set_index true
-#define TS_SIGNATURE "rusEFI main.2024.09.20.XYZ.1349726135"
+#define TS_SIGNATURE "rusEFI main.2024.09.21.XYZ.1057972626"
 #define TS_SIMULATE_CAN '>'
 #define TS_SIMULATE_CAN_char >
 #define TS_SINGLE_WRITE_COMMAND 'W'

generated/controllers/generated/signature_XYZ.h

@@ -2,5 +2,5 @@
 // was generated automatically by rusEFI tool config_definition-all.jar based on gen_config.sh by SignatureConsumer
 //
 
-#define SIGNATURE_HASH 1349726135
-#define TS_SIGNATURE "rusEFI main.2024.09.20.XYZ.1349726135"
+#define SIGNATURE_HASH 1057972626
+#define TS_SIGNATURE "rusEFI main.2024.09.21.XYZ.1057972626"

generated/live_data_generated/output_channels_generated.h

@@ -160,7 +160,7 @@ struct output_channels_s {
 	uint16_t RPMValue = (uint16_t)0;
 	/**
 	 * dRPM
-	 * units: RPM acceleration
+	 * units: RPM acceleration/Rate of Change/ROC
 	 * offset 6
 	 */
 	int16_t rpmAcceleration = (int16_t)0;

generated/tunerstudio/generated/rusefi_XYZ.ini

@@ -38,12 +38,12 @@ enable2ndByteCanID = false
 
 [MegaTune]
  ; https://rusefi.com/forum/viewtopic.php?p=36201#p36201
-	signature	= "rusEFI main.2024.09.20.XYZ.1349726135"
+	signature	= "rusEFI main.2024.09.21.XYZ.1057972626"
 
 [TunerStudio]
 	queryCommand	= "S"
 	versionInfo	= "V"  ; firmware version for title bar.
-	signature= "rusEFI main.2024.09.20.XYZ.1349726135" ; signature is expected to be 7 or more characters.
+	signature= "rusEFI main.2024.09.21.XYZ.1057972626" ; signature is expected to be 7 or more characters.
 
 	; TS will try to use legacy temp units in some cases, showing "deg F" on a CLT gauge that's actually deg C
 	useLegacyFTempUnits = false
@@ -485,7 +485,7 @@ enableLaunchRetard = bits, U32, 920, [4:4], "false", "true"
 canInputBCM = bits, U32, 920, [5:5], "false", "true"
 consumeObdSensors = bits, U32, 920, [6:6], "false", "true"
 enableCanVss = bits, U32, 920, [7:7], "false", "true"
-enableInnovateLC2 = bits, U32, 920, [8:8], "false", "true"
+unusedSnableInnovateLC2 = bits, U32, 920, [8:8], "false", "true"
 showHumanReadableWarning = bits, U32, 920, [9:9], "false", "true"
 stftIgnoreErrorMagnitude = bits, U32, 920, [10:10], "false", "true"
 vvtBooleanForVerySpecialCases = bits, U32, 920, [11:11], "false", "true"
@@ -775,8 +775,8 @@ invertExhaustCamVVTSignal = bits, U32, 1492, [29:29], "Rising", "Falling"
 enableKnockSpectrogram = bits, U32, 1492, [30:30], "false", "true"
 afterCrankingIACtaperDuration = scalar, S16, 1496, "cycles", 1, 0, 0, 5000, 0
 iacByTpsTaper = scalar, S16, 1498, "percent", 1, 0, 0, 500, 0
-auxSerialTxPin = bits, U16, 1500, [0:8], $gpio_list
-auxSerialRxPin = bits, U16, 1502, [0:8], $gpio_list
+unusedAuxSeria = bits, U16, 1500, [0:8], $gpio_list
+unusedAuxSerialRx = bits, U16, 1502, [0:8], $gpio_list
 accelerometerCsPin = bits, U16, 1504, [0:8], $gpio_list
 coastingFuelCutVssLow = scalar, U08, 1506, "kph", 1, 0, 0, 255, 0
 coastingFuelCutVssHigh = scalar, U08, 1507, "kph", 1, 0, 0, 255, 0
@@ -790,7 +790,7 @@ fan1ExtraIdle = scalar, U08, 1519, "%", 1, 0, 0, 100, 0
 uartConsoleSerialSpeed = scalar, U32, 1520, "BPs", 1, 0, 0, 1000000, 0
 tpsDecelEnleanmentThreshold = scalar, F32, 1524, "roc", 1, 0, 0, 200, 1
 tpsDecelEnleanmentMultiplier = scalar, F32, 1528, "coeff", 1, 0, 0, 200, 2
-auxSerialSpeed = scalar, U32, 1532, "BPs", 1, 0, 0, 1000000, 0
+unusedAuxSerialSpee = scalar, U32, 1532, "", 1, 0, 0, 100, 0
 throttlePedalSecondaryUpVoltage = scalar, F32, 1536, "voltage", 1, 0, -6, 6, 2
 throttlePedalSecondaryWOTVoltage = scalar, F32, 1540, "voltage", 1, 0, -6, 6, 2
 canBaudRate = bits, U08, 1544, [0:2], "50kbps", "83.33kbps", "100kbps", "125kbps", "250kbps", "500kbps", "1Mbps", "INVALID"
@@ -2075,8 +2075,6 @@ boardSpecificCalibration1 = scalar, S32, 22968, "", 1, 0, 0, 100, 0
 	enableAemXSeriesEgt = "AEM X-Series EGT gauge kit or rusEFI EGT sensor from Wideband controller"
 	afterCrankingIACtaperDuration = "This is the duration in cycles that the IAC will take to reach its normal idle position, it can be used to hold the idle higher for a few seconds after cranking to improve startup.\Should be 100 once tune is better"
 	iacByTpsTaper = "IAC Value added when coasting and transitioning into idle."
-	auxSerialTxPin = "Auxiliary sensor serial, not to be confused with secondary calibration serial"
-	auxSerialRxPin = "Auxiliary sensor serial, not to be confused with secondary calibration serial"
 	coastingFuelCutVssLow = "Below this speed, disable DFCO. Use this to prevent jerkiness from fuel enable/disable in low gears."
 	coastingFuelCutVssHigh = "Above this speed, allow DFCO. Use this to prevent jerkiness from fuel enable/disable in low gears."
 	tpsAccelEnrichmentThreshold = "Maximum change delta of TPS percentage over the 'length'. Actual TPS change has to be above this value in order for TPS/TPS acceleration to kick in."
@@ -2594,7 +2592,7 @@ dfcoActive = bits, U32, 0, [26:26]
 sd_active_wr = bits, U32, 0, [27:27]
 sd_active_rd = bits, U32, 0, [28:28]
 RPMValue = scalar, U16, 4, "RPM", 1, 0
-rpmAcceleration = scalar, S16, 6, "RPM acceleration", 1, 0
+rpmAcceleration = scalar, S16, 6, "RPM acceleration/Rate of Change/ROC", 1, 0
 speedToRpmRatio = scalar, U16, 8, "value", 0.01, 0
 unusedVehicleSpeedKph = scalar, U08, 10, "kph", 1, 0
 internalMcuTemperature = scalar, S08, 11, "deg C", 1, 0
@@ -3635,15 +3633,16 @@ unusedAtTheExtraEnd92 = scalar, U08, 1851, "", 1, 0
 	maintainConstantValue = throttlePedalWOTVoltage, { (calibrationMode == 13 ) ? calibrationValue  : throttlePedalWOTVoltage }
 	maintainConstantValue = throttlePedalSecondaryWOTVoltage, { (calibrationMode == 13 ) ? calibrationValue2 : throttlePedalSecondaryWOTVoltage }
 
+  requiresPowerCycle = isSdCardEnabled
+  requiresPowerCycle = sdCardSpiDevice
+  requiresPowerCycle = sdCardCsPin
 	requiresPowerCycle = boardUseCanTerminator
 	requiresPowerCycle = injectorCompensationMode
 	requiresPowerCycle = lps25BaroSensorScl
 	requiresPowerCycle = lps25BaroSensorSda
 	requiresPowerCycle = binarySerialTxPin
 	requiresPowerCycle = binarySerialRxPin
 	requiresPowerCycle = tunerStudioSerialSpeed
-	requiresPowerCycle = auxSerialRxPin
-	requiresPowerCycle = auxSerialTxPin
 
 	requiresPowerCycle = is_enabled_spi_1
 	requiresPowerCycle = is_enabled_spi_2
@@ -8105,8 +8104,6 @@ dialog = lambda_monitorDialog, "lambda_monitor"
 		field = "TLE8888 Chip Select",						tle8888_cs 
 		field = "TLE 8888 spi",								tle8888spiDevice 
 		field = "L9779 Chip Select",						l9779_cs 
-		field = "AUX Serial TX",						auxSerialTxPin
-		field = "AUX Serial RX",						auxSerialRxPin
 		field = "Start/Stop Button",					startStopButtonPin
 		field = "Upshift Pin",							tcuUpshiftButtonPin
 		field = "Downshift Pin",						tcuDownshiftButtonPin
@@ -8361,15 +8358,11 @@ dialog = lambda_monitorDialog, "lambda_monitor"
 		field = flipWboChannels,          flipWboChannels
 		field = "Force O2 sensor heating", forceO2Heating
 
-	dialog = uegoSerial, "Innovate LC-2 serial"
-		field = "Enable Innovate LC-2 Serial",			enableInnovateLC2, { auxSerialRxPin && auxSerialTxPin }
-
 	dialog = egoSettings, "", yAxis
 		panel = uegoCan
-		panel = uegoSerial
 		panel = egoSettings_IO1
-		panel = egoSettings_IO2, {afr_hwChannel != 0 && enableAemXSeries == 0 && !auxSerialRxPin && !auxSerialTxPin}
-		panel = egoSettings_sensor, {afr_hwChannel != 0 && enableAemXSeries == 0 && !auxSerialRxPin && !auxSerialTxPin}
+		panel = egoSettings_IO2, {afr_hwChannel != 0 && enableAemXSeries == 0}
+		panel = egoSettings_sensor, {afr_hwChannel != 0 && enableAemXSeries == 0}
 
 ;			Engine->EGT inputs
 	dialog = egtInputsCan, "CAN EGT sensors"
@@ -8985,21 +8978,16 @@ dialog = lambda_monitorDialog, "lambda_monitor"
 		panel = canHw1
 		panel = canHw2	
 
-	dialog = auxSerial, "AUX Sensor Serial"
-		field = "RX pin",								auxSerialRxPin 
-		field = "TX pin",								auxSerialTxPin 
-		field = "Serial Baud Rate",						auxSerialSpeed 
-
 	dialog = sdCard, "SD Card Logger"
 		field = "#rusEFI logs to SD when powered without USB connected"
 		field = "# and USB not connected for 15 seconds"
 		field = "#rusEFI connects SD to your PC when powered by USB"
 		field = "Enable SD Card",						isSdCardEnabled
-		field = "alwaysWriteSdCard",      alwaysWriteSdCard
-		field = "CS Pin",								sdCardCsPin			
-		field = "SPI",									sdCardSpiDevice		
-		field = "SD logger rate",						sdCardLogFrequency
-		field = "SD logger mode",						sdTriggerLog
+		field = "alwaysWriteSdCard",      alwaysWriteSdCard, { isSdCardEnabled }
+		field = "CS Pin",								sdCardCsPin, { isSdCardEnabled }			
+		field = "SPI",									sdCardSpiDevice, { isSdCardEnabled }		
+		field = "SD logger rate",						sdCardLogFrequency, { isSdCardEnabled }
+		field = "SD logger mode",						sdTriggerLog, { isSdCardEnabled }
 
 	dialog = tle8888Dialog, "TLE8888", yAxis
 		field = "TLE8888 SPI",							tle8888spiDevice 
@@ -9016,7 +9004,6 @@ dialog = lambda_monitorDialog, "lambda_monitor"
 	dialog = connection, "",	yAxis
 		panel = tsPort							
 		field = "uartConsoleSerialSpeed",				uartConsoleSerialSpeed
-		panel = auxSerial
 		field = enableKline, enableKline
 
 	dialog = monitoringSettings, "rusEFI Console Settings"

generated/tunerstudio/generated/signature_XYZ.txt

@@ -1,4 +1,4 @@
 ! Generated by gen_signature.sh
 ! SIGNATURE_HASH is a built-in variable generated by config_definition-all.jar
 ! gen_signature.sh Using env variable branch [main]
-#define TS_SIGNATURE "rusEFI main.2024.09.20.XYZ.@@SIGNATURE_HASH@@"
+#define TS_SIGNATURE "rusEFI main.2024.09.21.XYZ.@@SIGNATURE_HASH@@"